Bunn CT - Manuals - manualsarea.com

Page 2 - MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.; The agents, dealers or employees of BUNN; SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.; trademarks or registered trademarks of Bunn-O-Matic Corporation.

Page 2 41721 051910 BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years. 3) Comp...

Page 3 - INTRODUCTION; indoor use on a sturdy counter.

Page 3 41721 111308 USER NOTICES ........................................................................................................................................... 4 ELECTRICAL REQUIREMENTS ........................................................................................................

Page 4 - USER NOTICES; good condition. Replace any unreadable or damaged labels.; APS MODELS; THREE WARMER BREWERS; TWO WARMER BREWERS; ONE WARMER MODELS

Page 4 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. #12364.0000 WARNING ! Fill water tank before turning - on - thermostat or connecting appliance to pow...

Page 5 - CAUTION –; single phase models; Note: This electrical service; phase models; Some Twins require two individual power cords.

Page 5 ELECTRICAL HOOK-UP CAUTION – Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service as specified. 2. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source. FIG. 5-1 Dual Volt Switch Posit...

Page 6 - PLUMBING REQUIREMENTS-CURRENT SINGLES; water inlet fitting is

Page 6 PLUMBING REQUIREMENTS-CURRENT SINGLES As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow pre- vention to comply with federal, state and loc...

Page 7 - TWINS; PLUMBING REQUIREMENTS-CURRENT TWINS

Page 7 1. Remove six screws securing rear utility cover (if equipped). FIG 7-1 2. Remove cap from the flared fitting on the bottom of the center tube assembly. 3. Flush the water line and securely attach it to the flare fitting on the center tube assembly. FIG 7-2 4. Turn on the water supply. 5. Re-...

Page 8 - PLUMBING REQUIREMENTS-EARLY SINGLES

Page 8 PLUMBING REQUIREMENTS-EARLY SINGLES MODEL C: This model is completely portable and requires no attached plumbing. MODELS CT, CTF, CWT, CWTA, CWTB, CWTF, CWTFA & CWTFB, SINGLE CW & SINGLE CWF These brewers must be connected to a cold water system with operating pressure between 20 and ...

Page 9 - PLUMBING REQUIREMENTS-EARLY TWINS

Page 9 P1241 TWINS TWINS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the brewer. Install a regulator in the line when pressure ...

Page 10 - Adjusting Brew Volumes; ADJUSTING BREW VOLUMES

Page 10 INITIAL SET-UP CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails. 2. Place an empty dispenser under the funnel. 3. Place the heater switch at the rear of th...

Page 11 - THERMOSTAT KNOB; NOTICE; THERMOSTAT; procedure until all batch sizes are set.; Setting programming disable feature.; DUAL VOLT SWITCH

Page 11 SET/LOCK SWITCH THERMOSTAT KNOB FIG 11-1 LOCK SET -1000 213.8 101.0 200 93.3 -500 212.9 100.5 200 93.3 0 212.0 100.0 200 93.3 500 211.1 99.5 200 93.3 1000 210.2 99.0 200 93.3 1500 209.3 98.5 200 93.3 2000 208.4 98.0 200 93.3 2500 207.4 97.4 200 93.3 3000 206.5 96.9 199 92.8 3500 205.6 96.4 1...

Page 12 - OPERATING CONTROLS; BREW START SWITCH; AUXILIARY BREW START SWITCH

Page 12 ON/LOWER SWITCH Placing the "ON/LOWER" switch in the "OFF" (lower) position stops brewing. Stopping a brew cycle after it has been started, will not stop the flow of water into the funnel until the tank siphons down to its proper level. Placing the switch in the "ON" ...

Page 13 - NOTE –; er circuits are not affected. All Twins have 2 tank heater switches.; EARLY MODEL SWITCHS

Page 13 MASTER ON/OFF SWITCH(S) The master ON/OFF switch disables power the entire brewer (including tank heaters). NOTE – TWINS with 2 power cords will have 2 power switches, (one left, one right). TANK HEATER ON/OFF SWITCH(S) The tank heater ON/OFF switch disables power to the tank heater circuits...

Page 14 - COFFEE BREWING; filter into the funnel.; HOT WATER FAUCET; Faucet will not

Page 14 COFFEE BREWING 1. Insert a BUNN ® filter into the funnel. 2. Pour the fresh coffee into the filter and level the bed of grounds by gently shaking. 3. Slide the funnel into the funnel rails. 4. Place an empty dispenser beneath the funnel. 5. Place the "ON/OFF" switch in the "ON...

Page 15 - in the brewer and takes less than a minute.; BREWER IS DISCONECTED FROM WATER LINE.; Twist deliming spring while pushing in

Page 15 Clean Sprayhead Holes FIG 15-3 1. The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Use care when cleaning around the heater switch with a cloth, so as not to accidentally turn off the tank heater! 2...

Page 16 - TROUBLESHOOTING; WARNING –

Page 16 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic Technical Service Department. • Inspection, testing, and repair of...