Broan E662 - Manuals - manualsarea.com

Page 3 - TABLE OF CONTENTS

- 3 - TABLE OF CONTENTS BROAN ELITE E662 H OOD S YSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1. I NSTALL D UCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2. P REPARE THE...

Page 4 - BROAN ELITE E662 HOOD

- 4 - HL0055 Model 415 7” adjustable elbow (optional) 8” round adjustable elbow (optional) BROAN ELITE E662 HOOD BROAN ELITE E662HOOD SYSTEM Model 412transition(3¼” x 10”to 7” round) Model T460transition(3¼” x 14”to 7” round) Model 459 transition (3¼” x 14” to 8” round) Adapter and damper 3¼” x 14”(...

Page 5 - Distances over 30” are at the installer and users discretion.; PREPARE THE INSTALLATION; Make sure that the following items are included:; CABINET BOTTOM

- 5 - 1. INSTALL DUCTWORK Plan where and how the ductwork will be installed. Install proper-sized ductwork, elbows and roof or wall cap for the typeof blower you are installing. Use 2” duct tape to seal duct joints.NOTE: When performing vertical exhaust ductwork, there must be at least 14” high free...

Page 6 - CABINET PREPARATION; WARNING; See figures below for cut-out dimensions for ducting.

- 6 - 3. CABINET PREPARATION WARNING The cabinet must be sized to support the total weight of the hood. For the E662 hood model, thetotal weight is 41 lb (19 kg). ! If the cabinet need to be reinforced, we suggest to add wood blocks thestrengthen the connection between the bottom of the cabinet and ...

Page 7 - BLACK wire with red connector (; DO NOT FORGET TO CONNECT THE GROUND.

- 7 - 5. PREPARE THE HOOD 5.1 Remove filters from the hood. Remove (3) screws holding both sidepanels to the hood and set aside. Remove both side panels. 5.2 Punch out 2 knock-out holes for electrical connections (2 on top or one on top and one on back of the hood). 5.3 Attach one wire clamp on top ...

Page 8 - VERTICAL DISCHARGE ONLY

- 8 - 6. INSTALL THE HOOD (CONT’D) 6.3 Attach the second wire clamp, insert the power cable in the hood and tighten the wire clamp to secure the cable. Place the hood under the cabinet and slide it in position. Run power cable from hood up through slot cut in cabinet. Tighten the (4) screws complete...

Page 9 - INSTALL THE BLOWER IN THE CABINET; ALL DISCHARGE TYPES; Plug the cabinet blower to the hood receptacle.

- 9 - 8. INSTALL THE BLOWER IN THE CABINET 8.1 Install the cabinet in the cabinet and rest it on th e adapter plate. If a framed cabinet is used, insert the bloweras show in pictures below. 8.3 ALL DISCHARGE TYPES 8.2 VERTICAL DISCHARGE ONLY 8.2.1 Using four (4) no. 8 x 1/2” screws provided with hoo...

Page 10 - REINSTALL SIDE PANELS; CAUTION; Connect cable into wiring box using provided wire connectors.; DO NOT FORGET TO CONNECT THE GROUND

- 10 - WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance withall applicable codes and standards. Before connecting wires, switch power off at service panel andlock service disconnecting means to prevent power from being switched on accidentally. ! ...

Page 11 - Purchase separately; Install trim rings by pushing upward.

- 11 - 11. LIGHT BULBS This hood must use 120V, 50W max., type MR16, GU10 shielded halogen lamps. ( Purchase separately ). NOTE: The rings must be removed from bottom banel before installing halogen lamps. WARNING In order to prevent the risk of personal injury, do not install a lamp identified for ...

Page 12 - OFF D; Touch this touch pad to turn off lighting.

- 12 - 12. OPERATION A. B LOWER OFF D ELAY TOUCH PAD : When a speed is selected, touch the delay touch pad to activate the delay function. The corresponding speed indicatorLED will start flashing to indicate this function is activated. Touch once for a 5-minute delay, twice for 10-minute delay,three...

Page 16 - WARRANTY; BROAN-NUTONE LLC ONE-YEAR LIMITED WARRANTY

- 16 - 16. WARRANTY WARRANTY BROAN-NUTONE LLC ONE-YEAR LIMITED WARRANTY Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be freefrom defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARENO OTHER ...