Broan 410 - Manuals - manualsarea.com

Page 2 - For a gas range

WARNING WARNING - 2 - TO REDUCE THE RISK OF FIRE, ELECTRICSHOCK OR INJURY TO PERSONS, OBSERVETHE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing...

Page 3 - POWER PACK

HL0126 - 3 - - EC62 SERIES POWER PACK SYSTEM - 3¼” X 10” A DAPTER /D AMPER ( SUPPLIED WITH SINGLE BLOWER POWER PACK ) S INGLE B LOWER (600 CFM , SUPPLIED WITH POWER PACK ) D UAL B LOWER (1000 CFM , SUPPLIED WITH POWER PACK ) L6230SS, L6236SS OR L6242SS C USTOM H OOD L INER (O PTIONAL ) S TANDARD 3¼”...

Page 4 - Distances over 30” are at the installer and users discretion.; at least 4 feet; below the bottom of the custom; WARNING

- 4 - 1. PREPARE THE INSTALLATION 2. INSTALL DUCTWORK AND ELECTRICAL WIRING Plan where and how the ductwork will be installed. Access to the top of the power pack is preferred for connection of ductwork. Install proper-sized ductwork, elbows and roof or wall cap for the type of power pack you are in...

Page 5 - PREPARE CUSTOM HOOD; TOP VIEW

NOTE: The dual blower model has the same dimensions than the single blower model, but does not have a horizontal discharge. Refer to single blower power pack illustration for back and side views, and discard horizontal discharge measurements. 3. PREPARE CUSTOM HOOD The custom hood must be constructe...

Page 6 - NOTE: The liner must be installed before the insert.; CUT THE HOLE IN CUSTOM HOOD BASE; Keep in mind that the unit exterior flange is 3/4’’.

- 6 - 4. INSTALL CUSTOM HOOD LINER (OPTIONAL) The liners are specially designed to protect the exterior base of the custom hood. Toorder, refer to the table below to find the right liner model number according to thewidth of the custom hood nominal width. To view specific model information, includin...

Page 7 - REMOVE WIRING COVER AND FRONT PANEL

Using a Robertson or a Phillips no. 2 screwdriver, remove both wiring coverretaining screws ( A ). Detach it from the power pack and set aside with its screws. Then, remove both sides screws ( B ) retaining the front panel to the power pack. Carefully detach the front panel from the power pack and s...

Page 9 - INSTALL THE POWER PACK; ERTICAL; CAUTION; INSTALL THE ADAPTER/DAMPER ON BACK OF POWER PACK; WALL

- 9 - 14. INSTALL THE POWER PACK Lift the power pack in custom hood until the bottom of the clasping springs (2 per side) rests on the top of the custom hood base (grey zone in illustration at right). From inside the power pack, using provided no. 8-10 x 1/2” screws, mount the power packto the custo...

Page 11 - REINSTALL FILTERS

19. REINSTALL FILTERS 1. Using a Phillips no. 2 screwdriver, assemble the knob to each filter. NOTE: The screw MUST BE on filter tabs side. See illustration at right. CAUTION Remove protective plastic film covering filters before installing them. HO01 3 9 - 11 - 2. Rest rear filters edge on filter s...

Page 13 - ONE YEAR LIMITED WARRANTY FOR BROAN ELITE PRODUCTS

- 13 - 24. WARRANTY 23. WIRING DIAGRAM K1 BLK BLACK BLU BLUE BRN BROWN GRY GREY ORG ORANGE RED RED WHT WHITE YEL YELLOW COLOR CODE LINE GROUND NEUTRAL 120 VAC WHT BLK YEL WHT YEL BLK YEL WHT J1 WHT J2 GRY BRN RED BLK ORG WHT BLU WHT BLU ORG BLK WHT BLU WHT ORG BLK WHT BLU WHT ORG BLK 1 2 3 1 2 3 4 5...

Page 14 - LED

- 14 - 25.SERVICE PARTS EC621306SS EC622301SS 1 1 HL0169 2 3 4 2 7 9 9 10 10 11 K EY NO . P ART NO . D ESCRIPTION Q TY . (P OWER P ACK M ODEL ) EC621306SS EC622301SS 1 SV13296 A DAPTER /D AMPER 3¼” X 10” 1 - SV08541 A DAPTER 10” R OUND - 1 2 SV09226 E LECTRONIC C ONTROL WITH C HROMED B UTTONS AND B ...