Briggs & Stratton 2700PSI - Manuals

Briggs & Stratton 2700PSI – Manual in PDF format online.

Manuals:

Manual

Manual Briggs & Stratton 2700PSI

Summary

Page 2 - TABLE OF CONTENTS; WARNING

Snapper 2700 PSI Pressure Washer 2 TABLE OF CONTENTS Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Know Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . 4Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7Operatio...

Page 4 - KNOW YOUR PRESSURE WASHER

Snapper 2700 PSI Pressure Washer 4 KNOW YOUR PRESSURE WASHER Read this owner’s manual and safety rules before operating your pressure washer.Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls andadjustments. Save this manual for future ...

Page 5 - REMOVE PRESSURE; Carton Contents; PREPARING PRESSURE; Attach Handle to the Pressure

Snapper 2700 PSI Pressure Washer 5 IMPORTANT: Read entire owner’s manual before youattempt to assemble or operate your new pressure washer. REMOVE PRESSURE WASHER FROMCARTON • Remove all accessories and parts bag included with pressure washer. • Slice two corners at the end of carton from top to bot...

Page 6 - Install Oil Dipstick on Pump; Add Engine Oil

Snapper 2700 PSI Pressure Washer 6 • Insert the “L” bolt through the hole on the right side of the handle (viewing from rear of unit) and attach theplastic knob (Figure 2). Tighten the knob by hand. If notinstalled, add the vinyl cap to the “L” bolt. • Insert the multi–colored nozzles in the spaces ...

Page 7 - Connect Hose and Water Supply to

Snapper 2700 PSI Pressure Washer 7 Connect Hose and Water Supply to Pump IMPORTANT: You must assemble the nozzle extensionto the spray gun and attach all hoses before you start theengine. Starting engine without all hoses connected andwater supplied will damage the pump. • Uncoil high pressure hose ...

Page 8 - HOW TO USE YOUR; How to Start Your Engine

Snapper 2700 PSI Pressure Washer 8 HOW TO USE YOUR PRESSURE WASHER If you have any problems operating your pressure washer,please contact the local Snapper service center. How to Start Your Engine The best way to start your pressure washer for the firsttime is to follow these instructions step–by–st...

Page 9 - How to Stop Your Pressure Washer

Snapper 2700 PSI Pressure Washer 9 • If the choke lever has been moved to the “Choke” position to start the engine, gradually move it to the“Run” position as the engine warms up. • Attach the nozzle extension to the spray gun. Tighten by hand (Figure 12). • Select the desired quick connect nozzle an...

Page 10 - Cleaning and Applying Chemical; Pressure Washer Rinsing

Snapper 2700 PSI Pressure Washer 10 Cleaning and Applying Chemical CAUTION! You must attach all hoses before you start the engine. Starting the engine without all the hosesconnected and without the water turned ON will damagethe pump. IMPORTANT: Use soaps designed specifically forpressure washers. H...

Page 11 - SPECIFICATIONS; BEFORE EACH USE; PRESSURE WASHER; Check and Clean Inlet Screen; Check Detergent Siphoning Tube

Snapper 2700 PSI Pressure Washer 11 SPECIFICATIONS Rated Pressure . . . . . 2700 PSI Flow Rate . . . . . . . . . . 2.5 gallons per minute (gpm) Detergent . . . . . . . . . . Use detergent approved for pressure washers Water SupplyTemperature . . . . . . . Not to exceed 100°F Automatic Cool . . . . W...

Page 12 - Check Gun and Nozzle Extension; Nozzle Maintenance

Snapper 2700 PSI Pressure Washer 12 Check Gun and Nozzle Extension Examine the hose connection to the spray gun and makesure it is secure. Test the trigger by pressing it and makingsure it springs back into place when you release it. Put thesafety latch in the on position and test the trigger. Yoush...

Page 13 - O–Ring Maintenance; ENGINE MAINTENANCE; PREPARING THE UNIT

Snapper 2700 PSI Pressure Washer 13 6. Reinstall the nozzle and in-line filter into the nozzleextension. Do Not overtighten the nozzle with theallen wrench. 7. Reconnect the nozzle extension to the spray gun. 8. Reconnect the water supply, turn on the water, andstart the engine. 9. Test the pressure...

Page 14 - NOTES

Page 15 - TROUBLESHOOTING; Problem

Snapper 2700 PSI Pressure Washer 15 TROUBLESHOOTING Problem Cause Correction Pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, low water volume. 1. Low pressure nozzle installed. 2. Water inlet is blocked. 3. Inadequate water supply. 4. Inlet h...

Page 16 - EXPLODED VIEW — UNIT

Snapper 2700 PSI Pressure Washer 16 EXPLODED VIEW — UNIT

Page 17 - PARTS LIST — UNIT

Snapper 2700 PSI Pressure Washer 17 PARTS LIST — UNIT Item Part # Qty. Description 1 L190336GS 1 BASE 2 B2043GS 7 BOLT, 5/16" - 18 x 1-3/4"Carriage 3 187978GS 1 KIT, Handle Hardware 4 C190293GS 1 HANDLE 5 CB1981GS 2 SUPPORT, Handle 6 99583GS 8 NUT, 5/16" - 18 Hex Flange 7 B2150GS 1 HOOK,...

Page 18 - EXPLODED VIEW — PUMP

Snapper 2700 PSI Pressure Washer 18 EXPLODED VIEW — PUMP

Page 19 - PARTS LIST — PUMP

Snapper 2700 PSI Pressure Washer 19 PARTS LIST — PUMP Item Part # Qty Description 1 110B2126GS 1 Cap 2 10887628PGS 1 Circlip 3 112B2126GS 1 Snap Ring 4 113B2126GS 1 Bearing 5 109B2126GS 1 Pump Body 6 11287628PGS 1 Oil Cap/Dipstick 7 11187822PGS 3 Nut 8 11187822PGS 3 Piston Washer 9 123B2126GS 3 Pist...

Page 20 - EXPLODED VIEW — UNLOADER

Snapper 2700 PSI Pressure Washer 20 EXPLODED VIEW — UNLOADER

Page 21 - PARTS LIST — UNLOADER

Snapper 2700 PSI Pressure Washer 21 PARTS LIST — UNLOADER Item Part # Qty Description 0 153B2126GS 0 Complete Unloader 1 A1041GS 1 Filter, Chem 2 A1040DGS 1 Hose, Chem 3 48031GGS 1 Clamp, Hose band 4 210B2327GS 1 Hose Tail 5 95458GS 1 Quick Disconnect 6 231B2327GS 3 O-Ring 7 211B2327GS 1 Stainless B...