Bosch tc9346a - Manuals - manualsarea.com

Page 2 - CONTENTS; LIST OF ILLUSTRATIONS

2 CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION ..............................................................................

Page 3 - Only use replacement parts recommended by manufacturer.; The product and/or manual may bear the following marks:; RISK OF

3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and servicing should only be do...

Page 4 - OPTIONAL ACCESSORIES

4 2.0 DESCRIPTION Environmental enclosures in the TC9346A Series are used with pan/tilt units orfixed mounts. The enclosures are constructed of aluminum. You can install cameras with either fixed focal length lenses or motorized zoomlenses. All models have an adjustable camera sled to accommodate di...

Page 5 - Figure 1. Exploded Assembly Diagram for Blower and Circuit Board

5 3.0 INSTALLATION 1. Unlatch and raise the enclosure lid. The gas spring will hold the lid in placewhen it is fully opened. 2. Remove the camera sled from the rail: a. Loosen the screws. b. Slide the sled so that the screws are in the large part of the mountingslots. c. Remove the sled. d. Remove t...

Page 7 - or; You

7 b. Wire the 10-connector INPUTS terminal on the circuit board to the lenscontroller as follows: • Lens Common - Connector 1 • Focus - Connector 2 • Zoom - Connector 3 • Iris - Connector 4 • Preset Common - Connector 5 • Preset Focus - Connector 6 • Preset Zoom - Connector 7 • Preset High - Connect...

Page 9 - Figure 2. TC9346A Series Input Wiring Diagram

9 Figure 2. TC9346A Series Input Wiring Diagram KIT # BK57-2 KIT # BK57-1 (120 V) KIT # BK57-3 (230 V) FA N 24 VDC FA N 120/230 V PCB9000277ASSY RED BLK RED BLK 1 2 PLUG 1 2 PLUG BLK BLK PLUG 1 2 3 4 WHT WHT RED HEA TER 24/120/230 V HEA TER 24/120/230 V RED KIT # HK57-1 KIT # HK57-2 KIT # HK57-3 DEF...

Page 10 - Wire Gauge; Maxim; Table A. 24 VAC Wiring Distances; otal vA consumed; An enclosure that re-; Distances are calculated in

10 Wire Gauge Maxim um distance fr om transf ormer to load Table A. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applicationsand are calculated with a 10-percent voltage drop. (Ten percent is generally themaximum allowable voltage drop for AC-powered devices...

Page 11 - C) and to turn them off

11 4.0 OPERATION If your enclosure has a thermostatically controlled blower, the thermostat is set toturn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween 62 ° and 78 ° F (17 ° and 26 ° C). If your enclosure has thermostatically controlled heaters or defroster, ...

Page 12 - MAINTENANCE AND TROUBLESHOOTING; If your enclosure has a blower, clean the foam filters as follows:; Figure 3. Component Locations for Optional Circuit Board

12 5.0 MAINTENANCE AND TROUBLESHOOTING 5.1 MAINTENANCE Perform the following maintenance at regularly scheduled intervals to prolong theoperational life and appearance of the equipment. 1. Clean the window with a mild non-abrasive detergent in water and a soft clothto maintain picture clarity. 2. If...

Page 15 - Figure 6. TC9346A Dimension Drawing; GENERAL; IP32 (IP56 when vent cover plates are used)

15 Figure 6. TC9346A Dimension Drawing GENERAL NEMA Rating: 3R (4 when vent cover plates are used) iec 144 rating: IP32 (IP56 when vent cover plates are used) Environment: Indoor/outdoor -10 ° to 120 ° F (-23 ° to 49 ° C) (Design and product specifications subject to change without notice.) C A B 3....