Bosch F.01U.252.722 - Manuals

6 en | Safety instructions NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 1.4.1 Observation and information In case of defective operation or any other technical incident for which no remedy is described in this manual, please contact immediately your local repr...

NurseCall Relay Unit Description | en 7 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 2 Description 2.1 General description 2.1.1 Top view 1. Loudspeaker. See Section 2.2.1 Loudspeaker, page 10 . 2. Display. See Section 2.2.2 Display, page 10 . 3. Keyboard, under the cover. See Sec...

8 en | Description NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 2.1.2 Bottom view 1. Identification label. 2. Cable channels. 3. Wall mounting holes (distance between holes, 157 mm). See Section 3.2.3 Wall installation, page 14 for a detailed description. 4. O...

NurseCall Relay Unit Description | en 9 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 2.1.3 Front view 1. LED Indicator 2.1.4 Relay Unit rear view 1. RS-485 connector. See Section A.5.4 RS-485 socket (unit rear), page 34 for wiring. 2. Antenna connector 2.1.5 Relay Plus Unit rear v...

10 en | Description NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 2.2 Detailed description 2.2.1 Loudspeaker When one of the following alarms or messages is received by the NurseCall Relay Unit, the internal loudspeaker is activated until acknowledgement. 2.2.2...

NurseCall Relay Unit Description | en 11 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 Keys Function Access to the printer/display setup (Relay Plus Unit only) See Section 4.4 Printer/display setup on the Relay Plus Unit, Page 22 . Increase the volume of the loudspeaker. See Sectio...

12 en | Description NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 2.2.4 RS-485 interface One NurseCall Main Unit and up to 32 NurseCall Relay Units can be connected by a RS-485 bus. The bus must be connected to pins 2 and 5 of the RS-485 socket.  For connector...

NurseCall Relay Unit Installation | en 13 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 3 Installation 3.1 Unpacking The NurseCall Relay Unit is carefully packed for transportation. The components contained in the box are protected, but should be handled with care. Store the packag...

14 en | Installation NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 3.2 Installation 3.2.1 Generalities  Install the NurseCall Relay Unit in a dry place, away from any source of heat. Tools required: – Torx T20 screwdriver. – Torx T10 screwdriver. 3.2.2 Install...

NurseCall Relay Unit Installation | en 15 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 3.2.5 Connecting to the mains The NurseCall Relay Unit is powered by an adaptor (230/10 VAC or 115/10 VAC). 1. Plug the power adaptor into a power outlet placed near the unit. It should be easil...

16 en | Installation NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 3.2.6 Setting the jumpers on the communication board on the Relay Plus Unit 1. Disassemble the unit; see Section 6.5.1 Disassembling the unit, page 29 . 2. Remove the communication board; see Se...

NurseCall Relay Unit Installation | en 17 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 3.2.7 Connecting the RS-485 One NurseCall Main Unit and up to 32 NurseCall Relay Units can be connected to an RS-485 bus. Please contact a specialist for a correct installation.  See Section A....

18 en | Installation NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 3.2.8 Connecting the RS-232 to the Relay Plus Unit  Connect the printer or display device to the 9-pole SUB-D connector (1) at the rear part of the housing of the Relay Plus Unit. For connector...

NurseCall Relay Unit Programming | en 19 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 4 Programming 4.1 Generalities 4.1.1 Using the keyboard  Open the cover carefully and use the keyboard.  To access the special settings programming, press three times quickly. See Section 4.3 S...

20 en | Programming NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 4.2 First use 4.2.1 List of original factory settings * Locating mode and identification number are set at first use. To change a value, reset the unit. See Section 4.3.2 Resetting all the parame...

NurseCall Relay Unit Programming | en 21 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 Manual selection of the NurseCall Main Unit 5.a. Scroll with and to set manually the identification number. Confirm with or the Green button. The Relay Unit signalizes that it is not connected to...

22 en | Programming NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 4.3.4 Assistance and fire non priority This command sets the assistance call and the fire alarm as non-priority calls. This means that the last alarm is displayed, whatever its type. This is the ...

24 en | Programming NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems c. Choose 0 to 9 characters for the criterion, followed by 0 to 9 spaces. Default values are 2 characters + 1 space. 7. Repeat the operation for a. the floor ( 0 to 3 characters and 0 to 9 spaces...

NurseCall Relay Unit Operation | en 25 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 5 Operation 5.1 Adjusting the loudspeaker volume When the NurseCall Relay Unit is in standby mode:  Press to increase the volume.  Press to decrease the volume. 5.2 Consulting the alarm or event ...

26 en | Operation NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 5.2.1 Switching between alarm and event buffers indication The alarm buffer is indicated by default. If you are in the event buffer, the unit changes automatically to the alarm buffer after 1 minut...

NurseCall Relay Unit Operation | en 27 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 Third information block 8. position of the last passed beacon, visible in all display modes. If no beacon is registered or if the alarm is sent outside of the range of a beacon, the POS 000 will be...

28 en | Maintenance NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 6 Maintenance 6.1 Checking the system Check the correct function of your NurseCall system.  Perform periodically an alarm test. 6.2 Monitoring the power supply In case of a power failure, the Nu...

NurseCall Relay Unit Maintenance | en 29 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 6.4 Cleaning  Avoid using cleaning products or detergents.  Wipe off your NurseCall Relay Unit occasionally with a dry cloth. 6.5 Parts replacement 6.5.1 Disassembling the unit Removing the ant...

30 en | Maintenance NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems 6.5.2 Backup battery replacing Important Safety Instructions The battery should charge for 24 hours before using the NurseCall Relay Unit for the first time, after replacing the battery or after ...

NurseCall Relay Unit Disposal | en 31 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 7 Disposal The NurseCall Relay Unit is marked with a crossed-out wastebasket symbol. This means that, at the end of its lifetime, the product should be disposed separately from ordinary household wa...

32 en | NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems A Appendix A.1 Electrical specifications A.2 Dimensions and weight A.3 Environmental conditions Voltage 230 or 115/10VAC Current 280 mA Frequency 50/60 Hz Power 2.8 W max. Casing dimensions [mm] Depth 220 Wi...

NurseCall Relay Unit | en 33 Bosch Security Systems User Manual F.01U.252.722 | V1 | 2011.12 A.4 List of criteria Criterion Number Alarm (A) or Event (E) Comment ERROR 00 A System malfunction, e.g. component defective PERSONNEL A 01 E Coded key active (N46) LOW BATTERY 02 A Battery at low level (Tra...

34 en | NurseCall Relay Unit F.01U.252.722 | V1 | 2011.12 User Manual Bosch Security Systems A.5 Connectors A.5.1 LINE socket (unit bottom) A.5.2 Power socket (unit bottom) A.5.3 RS-232 socket (Relay Plus Unit rear) A.5.4 RS-485 socket (unit rear) LINE socket Wiring 1. Flash Data GND 2. Not used 3. ...