Bosch DKE 63 - Manuals - manualsarea.com

Page 2 - t r; Sayfa

2 mind. 650 mind. 550 de Seite 0 3 – 13 en page 14 – 24 fr page 25 – 35 nl pagina 36 – 46 it pagina 47 – 57 es página 58 – 68 Abb. 1 ELEKTROELECTR.ELETT.EL. Abb. 1GASGAZKAASUGASS pt página 0 69 – 0 79 sv sid 0 80– 0 90 no side 0 91– 101 fi sivu 102 – 112 da side 113 – 123 t r Sayfa 124 – 134

Page 3 - When the extractor hood is operated; Operating modes; from

14 Appliance description Operating Instructions Operating modes Exhaust-air mode: ❑ The extractor-hood fan extracts the kit-chen vapours and conveys them throughthe grease filter into the atmosphere. ❑ The grease filter absorbs the solid particles in the kitchen vapours. ❑ The kitchen is kept almost...

Page 4 - Repairs

Before using for the first time If you encounter a problem If you have any questions or if a faultoccurs, please call Customer Service. (See list of Customer Service representatives).When you call, please quote the following: E-Nr. FD Enter the relevant numbers into the boxabove. The E-Nr. (product ...

Page 5 - Cleaning the metal grease filters:; The most effective method of removing; Switch the ventilator ON; as soon as you begin cooking.; Switch the ventilator OFF; Slide the right slide switch back to

16 Operating procedure Filters and maintenance Grease filters: Metal filters are used to trap the greasyelement of the vapours that developduring cooking. The filter mats are made from non-combustible metal. Caution: As the filter becomes more and more saturated with grease, not only does therisk of...

Page 6 - Filters and maintenance; Replacing the activated carbon filters:; Activated carbon filter:

Filters and maintenance Removing and inserting the metal greasefilters: 1. Press the catch on the grease filtersinwards and fold the filters down. 3. Insert the grease filters (see removal andinstallation of the metal-mesh greasefilters). Removing the filter: The filters are removed in reverse seque...

Page 7 - Stainless steel surfaces:

18 Replacing the light bulbs 1. Switch off the extractor hood and pullout the mains plug or switch off the electricity supply at the fuse box. 2. Remove the grease filters (see Filters andMaintenance). 3. Press down the bulb cover and disconnect from the light strip. 4. Replace the bulb (standard fi...

Page 9 - Prior to installation; Exhaust air should neither be directed; which will be needed by the

20 Prior to installation Exhaust-air mode The exhaust air is discharged upwardsthrough a ventilation shaft or directlythrough the outside wall into the open. D Exhaust air should neither be directed into a smoke or exhaust flue that iscurrently used for other purposes, nor intoa shaft that is used f...

Page 10 - Flat ducts; Connecting a; For optimum extractor hood efficiency:

21 Prior to installation ❑ Flat ducts must have an internal cross- section that equates to that of roundpipes. There should be no sharp bends. l 100 mm approx. 1 78 cm 2 l 125 mm approx. 113 cm 2 ❑ If pipes have different diameters: Insert sealing strip. ❑ For exhaust-air mode, ensure that there is ...

Page 11 - The extractor hood; Electrical connection; from specialist; Preparing the wall; Exhaust air

22 Electrical connection This is what you have to do: 1. Connect the green and yellow (Earth) wire to the terminal in the plug marked‘E’ or with the symbol ( ), or coloured green or green and yellow. 2. Connect the blue (Neutral) wire to the terminal in the plug marked ‘N’ or coloured black. 3. Conn...

Page 12 - Installation; This extractor hood

23 Installation This extractor hood is intended to be mounted onto the kitchen wall. 1. Remove the grease filter (refer to Operating Instructions). 2. Draw a line on the wall from the ceilingto the lower edge of the hood at thecentre of the location where the hood isgoing to be mounted. 3. Using the...

Page 13 - Insert the other 4 screws with washers.; Before the 4 screws are tightened; Connect up the air outlet pipe.; Before tightening the 2 screws,; Avoid damage to the sensitive

24 Installation 0 8. Insert the other 4 screws with washers. Before the 4 screws are tightened down, align the extractor hood properly. 0 9. Connect up the air outlet pipe. 10. Connect the hood to the electricitysupply. 13. Position the lower flue duct on theextractor hood and screw the extractorhoo...

Page 14 - Notes

Page 16 - Robert Bosch Hausgeräte GmbH

9000 019 148 Printed in Germany 0904 Es. Robert Bosch Hausgeräte GmbH