Bosch APC-AMC2-4WUS - Manuals

Page 3 - Remarks

AMC2 4W | en 3 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Remarks This hardware is part of a security system. Access shall be lim- ited to authorized persons only. Some states do not allow the exclusion or limitation of implied warranties, or limitation of liability for...

Page 4 - Table of Contents; Please read carefully

4 en | AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems Table of Contents 1 Please read carefully 7 1.1 Explanation of Used Symbols 7 1.2 Internet 7 2 Safety Instructions 8 2.1 Important Safety Notes 8 2.2 FCC & ICES Information 10 2.3 Safety Precautions 11 2.4 Un...

Page 5 - Operating

AMC2 4W | en 5 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 5.9 RS-485 Extension Module Bus 39 5.10 Wiegand Interface for Card Readers 39 5.11 Connecting Relay Outputs 41 5.12 Connecting Analog Input Devices 44 5.13 Tamper Protection 46 6 Operating 48 6.1 Status Display o...

Page 7 - Explanation of Used Symbols

AMC2 4W Please read carefully | en 7 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 1 Please read carefully 1.1 Explanation of Used Symbols Throughout this document, helpful tips, important notes, cau- tions and warnings will be presented for the reader to keep in mind. The...

Page 8 - Safety Instructions; Important Safety Notes; Consider all Warnings

8 en | Safety Instructions AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 2 Safety Instructions 2.1 Important Safety Notes 1. Read, Follow, and Retain Instructions - All safety and operating instructions must be read and followed properly before putting the unit int...

Page 9 - Replacement Parts

AMC2 4W Safety Instructions | en 9 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 • If the unit has been dropped or the cabinet damaged. • If the unit exhibits a distinct change in performance, this indicates that service is needed. 7. Replacement Parts - When replacement p...

Page 10 - FCC & ICES Information

10 en | Safety Instructions AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 2.2 FCC & ICES Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, an...

Page 11 - Safety Precautions; Health and Safety

AMC2 4W Safety Instructions | en 11 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 2.3 Safety Precautions ! Read instructions! Before working with the AMC2 4W, read these instructions carefully. Make sure you have understood all information described in this document. ! War...

Page 12 - Unpacking; CAUTION: Lithium Battery

12 en | Safety Instructions AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 2.4 Unpacking Check the packaging for visual damage. If anything has been damaged during transport, make the transport agency aware of this. Carefully unpack the unit. This is an electronic d...

Page 13 - Introduction; Description of the AMC2 4W

AMC2 4W Introduction | en 13 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 3 Introduction 3.1 Description of the AMC2 4W The AMC2 4W is equipped with four independent interfaces for Wiegand type readers. By that it is able to control two doors with a reader in each directi...

Page 15 - Equipment Configuration

AMC2 4W Introduction | en 15 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 3.2 Equipment Configuration Fig. 3.3 Upper circuit board with display (top side) 1. Internal tamper contact 2. DIL switch for RS-485 address selection, protocol and RS- 232/RS-485 selection 3. Lithi...

Page 16 - Wiegand interfaces for up to 4 card readers (Pluggable

16 en | Introduction AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 11. Configurable RS-232 host interface (ribbon cable connec- tor) 12. Configurable 10/100 Mbit/s Ethernet interface Fig. 3.4 Overview - Interfaces 13. RS-485 extension module bus (Pluggable screw co...

Page 17 - Jumper: Selector for either potential free relay output or

AMC2 4W Introduction | en 17 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 3.5 Jumper at the bottom side 19. Jumper: Selector for either potential free relay output or powered by AMC2 4W internal power supply (wet/dry con- tacts). 20. Jumper: Potential equalization be...

Page 18 - Performance Characteristics

18 en | Introduction AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 3.3 Performance Characteristics – Intelligent access manager for 1 ... 4 entrances (e.g. doors, man traps, barriers) – Host address selectable via DIL sliding switch – Four possible configurable hos...

Page 19 - System Overview

AMC2 4W Introduction | en 19 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 3.4 System Overview The Access Controller AMC2 4W is connected between the management host system and different peripheral devices. By default a management host system is connected via Ethernet. A m...

Page 20 - Technical Data

20 en | Technical Data AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 4 Technical Data Hardware – Integrated Microcontroller (32Bit, 30MHz) – SRAM (256MB) – Serial EEPROM – RTC – Pluggable Compact Flash from 64 MB up to 1024 MB – Battery for SRAM and real time clock...

Page 22 - Installing; Mounting; mounting rail via a snap-in mechanism. Attach the AMC2 4W

22 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 5 Installing 5.1 Mounting The AMC2 4W can be attached on a standard 35 mm (1.377 in.) mounting rail via a snap-in mechanism. Attach the AMC2 4W into the upper edge of the mounting rail, then push down...

Page 23 - Demounting; Push down the AMC2 4W until it snaps out of the mounting rail.; To remove the AMC2 4W from a mounting rail, first, remove all

AMC2 4W Installing | en 23 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 5.2 Demounting Push down the AMC2 4W until it snaps out of the mounting rail. Pull the lower end of the AMC2 4W from the mounting rail. Fig. 5.2 Demounting the AMC2 4W from a mounting rail i NOTE! To ...

Page 24 - Opening the AMC2 4W Case; The AMC2 4W case consists of a top cover mounted with a two-; nectors at least the host connection.

24 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 5.3 Opening the AMC2 4W Case The AMC2 4W case consists of a top cover mounted with a two- point snap-in closure on a ground chassis. To open the AMC2 4W push down the two snap-ins with a srew driver. ...

Page 25 - Cabling; Grounding and Shielding; Conductor data for connection to power supply

AMC2 4W Installing | en 25 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 5.4 Cabling Grounding and Shielding The main grounding point at the AMC2 4W will be connected with pin 2 of the power supply connector - see Figure 7.6 . It is good practice to shield all wires carryi...

Page 26 - Critical condition! Install the power supply closer to the con-; Grounding and Shielding the Host Interface; The jumper setting A1 shows the delivery status.; km; ft; These specifications aim for readers, relay outputs, and exten-

26 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems U = 12V, I = 1A, maximum V Drop = 2V i.e. R AWG18 (acc. specs) = or 20,948 V Drop = 20,948 x 0.1 km x 1A = 2.1V V Drop = x 328 ft x 1A = 2.1V Critical condition! Install the power supply closer to the...

Page 28 - Grounding and Shielding the Extension Interface; Connecting Power Supply

28 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 5.4.3 Grounding and Shielding the Extension Interface Fig. 5.5 Location of ground jumper bottom side Jumper B connects the internal ground of the AMC2 4W to the RS-485 ground of the slave interface. J...

Page 30 - RS-485 Host Interface; An RS-485 host system can consist of up to eight AMC2 4W

30 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 5.6 RS-485 Host Interface An RS-485 host system can consist of up to eight AMC2 4W controllers connected via 2- or 4-wire connection. Fig. 5.7 Configuration of a RS-485 host system

Page 32 - RS-485 Two Wire Connection

32 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems Fig. 5.8 RS-485 host interface 5.6.1 RS-485 Two Wire Connection Fig. 5.9 Connection scheme of a RS-485 two wire connection

Page 33 - ON; Address Selector; RS-485 Four Wire Connection

AMC2 4W Installing | en 33 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 5.10 Settings for RS-485 two wire connections For RS-485 two wire connection set the AMC-MUX DIL-Switch at the position 3 , 7 and 8 to ON . On the upper side of the AMC panel put the jumper on th...

Page 34 - DIL Switch Address Selector

34 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems Fig. 5.12 Settings for RS-485 four wire connection For RS-485 four wire connection set the AMC-MUX DIL-Switch at the position 3 , 5 and 6 to ON . On the upper side of the AMC panel put the jumper on t...

Page 36 - RS-232 Host Interface

36 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 5.7 RS-232 Host Interface The AMC2 4W offers an RS-232 serial interface to connect a host computer or serial modem. Address DIL Switches 1 2 3 4 none OFF OFF OFF OFF 1 ON OFF OFF OFF 2 OFF ON OFF OFF ...

Page 37 - Ethernet Interface

AMC2 4W Installing | en 37 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 5.14 Location of the RS-232 serial interface The AMC is created like a PC, so you cannot build a 1:1 connec- tion, but cross the data wires using a null modem cable for example. 5.8 Ethernet Inte...

Page 39 - RS-485 Extension Module Bus; Wiegand Interface for Card Readers

AMC2 4W Installing | en 39 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 5.9 RS-485 Extension Module Bus The RS-485 Extension Module Bus expands the AMC2 4W with additional I/O modules (AMC2 8I-8O-EXT or AMC2 16I-16O- EXT). Up to three expansion modules can be connected to...

Page 41 - Connecting Relay Outputs; To operate locks or alarm systems the AMC2 4W has eight form; Each relay output can operate in ‘wet’ mode, using the

AMC2 4W Installing | en 41 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 5.11 Connecting Relay Outputs To operate locks or alarm systems the AMC2 4W has eight form C relay outputs. The outputs will be connected to the 3-pin pluggable screw connectors: S5, S6, S10, S11, S17...

Page 43 - Each relay output has a separate jumper setting on the bottom

AMC2 4W Installing | en 43 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 5.20 Schema of the using of the recovery diode Each relay output has a separate jumper setting on the bottom side of the lower circuit board to activate wet (D2)or dry (D1) mode. ! Risk of Damage...

Page 44 - Connecting Analog Input Devices; The AMC2 4W has eight analog inputs, for example, for poten-

44 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems Fig. 5.21 Location of relay output jumpers (bottom side) 5.12 Connecting Analog Input Devices The AMC2 4W has eight analog inputs, for example, for poten- tial free lock mechanisms or to detect if a l...

Page 46 - Tamper Protection

46 en | Installing AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems To detect the four states there are only special values allowed for potential drop depending on the used resistors. The follow- ing table shows the values for the possible resistor combina- tions. 5.1...

Page 48 - Status Display of the AMC2 4W; The LC Display delivers information about the AMC2 4W status.; The display mode which has been set remains until the next

48 en | Operating AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 6 Operating 6.1 Status Display of the AMC2 4W The LC Display delivers information about the AMC2 4W status. Push the 'Dialog' button to switch between different modes. Fig. 6.1 Location of the ’Dialog’...

Page 49 - Push

AMC2 4W Operating | en 49 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Push Display (Example) Description 0 V37.02 02.03.06 or WIEGAND Software versions and date of the downloader - every 5 sec. alternating with the display of the reader interface. (= default page) 1 9999...

Page 50 - Configuring the Ethernet Interface; AmcIpConfig; Resetting the AMC2 4W; Resetting the Software

50 en | Operating AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 6.2 Configuring the Ethernet Interface To configure the AMC2 4W in a TCP/IP network environment use the tool AmcIpConfig provided in the following directory on the standalone or the remote server: \\Ru...

Page 51 - Resetting the Network Configurations; Reset the AMC2 4W as described above (in download pro-; Press the tamper switch on the upper left side of the board

AMC2 4W Operating | en 51 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 6.2 Restarting the AMC2 4W with the provided screw driver 6.3.2 Resetting the Network Configurations 1. Reset the AMC2 4W as described above (in download pro- gram). 2. Open the upper case of the ...

Page 53 - Appendix; Connecting Diagrams

AMC2 4W Appendix | en 53 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 7 Appendix 7.1 Connecting Diagrams Fig. 7.1 Connectors on upper PCB Fig. 7.2 RS-485 host on upper PCB

Page 57 - Legend; Twisted pair connection

AMC2 4W Appendix | en 57 Bosch Security Systems Installation manual F.01U.024.965 | V.4 | 2006.09 Fig. 7.10 Extension interface Fig. 7.11 External tamper contact 7.2 Legend Twisted pair connection Transmitter Receiver

Page 58 - Index

58 en | Index AMC2 4W F.01U.024.965 | V.4 | 2006.09 Installation manual Bosch Security Systems 8 Index A Address Selector 34 Analog Input Devices 44 Appendix 53 C Cabling 25 Conductor data 25 Configuring the Ethernet Inter- face 50 Connecting Diagrams 53 D Demounting the AMC-4 23 Description of the ...