Bogen RM-350D - Manuals - manualsarea.com

Page 2 - Specifications; individual plus 1 All Call

Specifications Band Coverage . . . . . . . . . . . . AM . . . . . . . . . . . . . . . . . . . . .530 - 1620KHzFM . . . . . . . . . . . . . . . . . . . . . .87.5 - 107.9MHz Tuning . . . . . . . . . . . . . . . . . . . .PLL Synthesizer Channel Indicator . . . . . . . . . . .LCD panel Memory Presets . ...

Page 3 - Warning; Antenna Connection; FM Dipole Antenna; OHM BAL; Move the antenna around to determine the best reception; b) For applications using coaxial cable, a 75 OHM coaxial; cable connector is provided.

Before You Begin Your Bogen RM-350D Digital Tuner/Receiver incorporates thelatest in PLL digital circuitry for reliable performance for years tocome. To get the maximum benefit from your Bogen product,please read all instructional materials provided with the unit. Unpacking The RM-350D is carefully ...

Page 4 - AM Loop Antenna; Connect the antenna leads to the terminals marked AM; Fold the antenna so that it snaps into the base forming a; Microphone Connection; A VOX circuit activates; Music Muting

AM Loop Antenna The RM350D is provided with anexternal AM antenna for AM recep-tion. 1. Carefully pull the antenna lead from the holding notch in theantenna and unwind the leadfrom the loop. 2. Connect the antenna leads to the terminals marked AM ANT . 3. Fold the antenna so that it snaps into the b...

Page 5 - An ALC switch on the rear panel controls the ALC circuit. When; AUX Input; Connect an Aux source to the RCA jacked marked AUX.; PREPAGE OUT; Speaker Connections; Direct Connection; You can connect a 4-8; and GND as shown below. Remove the LINK for 4-8

1. Unplug the unit from electrical source. 2. Remove eight (8) screws securing the unit cover to the chassis. 3. Slide cover back to remove it from chassis.4. Locate Jumper J1 on the circuit board (right side of the unit as you look at it from front panel). 5. Reposition jumper from CLOSED position ...

Page 6 - Speaker Zone Connection; You can connect up to 4 separate speaker zones.; To connect zones of 4 - 8; ance selector jumper wire to the 4-8; terminal. Remove the; Connect only; For more than

25V & 70V Connection You can connect a 25 or 70V balanced or unbalanced line tothe terminals marked 25V or 70V and GND. 25V line connec-tion is shown below. Speaker Zone Connection You can connect up to 4 separate speaker zones. To connect zones of 4 - 8 Ω Ω speakers: Connect the imped- ance sel...

Page 7 - To connect zones using 25V or 70V line:; Connect the; Tape Out

To connect zones using 25V or 70V line: Connect the impedance selector jumper to the 25V or 70V terminal.Connect the line to the desired zone terminal and COM asshown below. Tape Out You can connect a tape recorder to the RM350D using the TapeOut jack. This jack provides a line level output consisti...

Page 8 - Operation

Operation Power Press the front panel POWER switch to apply power. Adjustthe volume to the appropriate level using the amplifier volumecontrol. To Select a Band Press the button marked BAND. The current band appears onthe display: FM1, FM2, FM3, AM1 or AM2. You can preset up to six stations on each ...

Page 9 - Microphone Volume; Use the MICROPHONE control to adjust mic volume.; Tone Controls

Microphone Volume Use the MICROPHONE control to adjust mic volume. Aux/Tuner Volume The VOLUME control adjusts the output level of program fromtuner and aux sources. It does not control the level of themicrophone program. Tone Controls Use the BASS and TREBLE controls to adjust tonal balance ofprogr...

Page 10 - Maintenance; CAUTION

Maintenance CAUTION There are no user serviceable parts within the tuner.To avoid an electric shock hazard, refer all internalservicing to qualified service personnel only. The warranty will become void if repairs are made byother than the Bogen Factory Service Center. We are interested in the maint...