BlueStar PM058ML - Manuals

• If a fire should occur, do not turn on hood to evacuate smoke. Turn off hood. • Do not use to exhaust hazardous, flammable or explosive materials. • Clean baffle filters often, since accumulated grease can be a fire hazard and affect the performance of your ventilation hood. WARNING Handling: • Do...

Installation of Ducting for Proper Operation: Proper installation of ducting is extremely important for optimal performance of your ventilation system. It is a basic requirement that the kitchen is provided with an air intake to ensure good air circulation and, therefore, proper operation of the hoo...

INSTALLATION INSTRUCTIONS Figure E: Remove Mounting Screws Remove Philips screws in front and back of liner that attach it to the outer shell. Screws are located behind scalloped detail in trough front and back. E. F. Step 3: Set liner aside and prepare for blower installation. 1. If a duct cover is...

INSTALLATION INSTRUCTIONS Step 4-3. Installing an Exterior Roof or Wall Mounted Remote Blower (HYEX) 10 Model Number: HYEX-1.0 / HY-EX-1.4 Maximum rated CFM: 1000 CFM / 1400 CFMVolts/Hz/Amps: 115VAC, 60 Hz, 2.9A (HYEX-1.0) / 3.3A (HYEX-1.4) Required duct size: HYEX- 1.0: 8” Round (51 sq. in. equiv.)...

Alternate Mounting Option 1. Use temporary fixtures you can later remove to hang the equipment at its proper elevation. (Vibration isolation mounts and associated hardware not included.) 2. Fasten the hanger directly to the structure or somewhere between the suspended unit. Do not overtighten the ne...

INSTALLATION INSTRUCTIONS Step 4-5. Wiring Remote Blowers (HYEX or ATEX) ELECTRICAL CONNECTIONS 1. Run a 3-conductor electrical cable between the blower and the range hood. Local building codes take precedence, but unless otherwise directed, use 14-2 MC shielded cable or equivalent. See Figure 4. 2....

5. Hardware is not provided with this unit to secure it to the wall. Local building codes take precedence (where applicable). Otherwise, use #12 screws or larger lag screws with a length such that at least 1” of thread is embedded into a structural member (i.e., wood stud or blocking) behind the mou...

INSTALLATION INSTRUCTIONS Step 7. Connect Ducting to Ventilation Hood Install ducting around starter collar on top or rear of hood and seal according to building code regulations. Be sure to include a back draft damper in the duct work to prevent drafts. Step 6. Re-install Liner into Outer Shell NOT...

INSTALLATION INSTRUCTIONS: DUCT COVERS Installing a Telescopic Duct Cover 1. Attach upper mounting bracket to wall against ceiling and centered with hood. 2. Attach lower mounting bracket to wall against top of hood shell. 3. Slide upper duct cover down into lower duct cover. 4. Place duct cover ass...

INSTALLATION INSTRUCTIONS Models starting with “MH” 1. Follow Step 2 of installation instructions on removing liner from outer shell. 2. The hood is provided with a preinstalled 3-prong cord to provide power to the hood and blower. • If an appropriate outlet is not accessible due to the installation...

USE & CARE INSTRUCTIONS Control Panel A B C D E F Blower Controls Light Controls Timer Blower Controls: A – Blower power on, power off, low speed B – Blower middle speed C – Blower high speed D – Blower Boost function* *After 7 minutes of operation, the blower will automatically move to high spe...

The function of the baffle filters is the absorption of grease particles that form during cooking. Do not operate ventilation hood without filters in hood. Baffle filters should be examined periodically to assure that the surfaces and parts are clean. IMPORTANT USE & CARE INSTRUCTIONS Baffle Fil...

USE & CARE INSTRUCTIONS Cleaning the Interior Clean the interior of the hood using a soft cloth and warm soapy water or denatured alcohol as needed. Do not clean the electrical parts or blower with liquids or solvents. Allow to dry thoroughly before restoring power. Cleaning the Exterior It is i...