BlueStar LP036LP - User Manual

HANDLING  REMOVE ALL WATCHES, BELT BUCKLES, JEWELRY, RINGS AND ANY CLOTHING WITH METAL BUTTONS OR SNAPS TO PREVENT DAMAGE TO THE HOOD.  WHEN YOU BEGIN THE INSTALLATION PROCESS REMOVE THE HOOD FROM IT’S ORIGI-NAL CARTON AND PLACE THE HOOD ON A CLEAN, NON-ABRASIVE BLANKET.  INSPECT THE HOOD CARE...

PACKING LIST FOR PRO LINE HOOD SERIES PL30240——24” depth  No blower (Sold and Packaged Separately)  Two (2) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram PL36240, PL42240—24” depth  No blower (Sold and Packag...

PACKING LIST FOR PYRAMID STYLE HOOD SERIES PC30240—24” depth  No blower (Sold and Packaged Separately)  Two (2) Stainless Steel Baffle Filters  Two (2) Pre-Installed Lights  Lid for Electrical Box  Use and Care Manual with Wiring Diagram  Duct cover sold packed in separate box (2 of2) PC...

DIMENSIONS OF THE PRO LINE SERIES HOOD  INLET LOCATION FOR THE ELECTRICAL CONNECTION IS LOCATED NEAR THE REAR CENTER OF HOOD 3-3/16” FROM HOOD BOTTOM.  ELECTRICAL REQUIREMENTS: 15 AMPS AT 120 VOLTS  LIGHT BULBS ARE HALOGEN G9, 120V, 25W  BULBS ARE OPERATED BY A DIMMER SWITCH  BLOWER IS VAR...

IN SELECTING THE PROPER HEIGHT TO MOUNT THE HOOD, TAKE INTO CONSIDERATION THE STATURE OF THE PERSON OR PERSONS WHO WILL BE COOKING. A HEIGHT OF 30", MINIMUM HEIGHT OFF OF COOKING SURFACE, TO 36" MAXIMUM HEIGHT OFF OF THE COOKING SURFACE, WILL SUIT MOST USERS. IF MOUNTED AT A HEIGHT GREATER T...

THE CORRECT HEIGHT OF YOUR PRO LINE SERIES HOOD THE BOTTOM OF THE HOOD SHOULD BE 30" MINIMUM TO 36" MAXIMUM ABOVE THE COUNTERTOP. THIS WOULD TYPICALLY RESULT IN THE BOTTOM OF THE HOOD BEING 66" TO 72" ABOVE THE FLOOR. THE BOTTOM OF THE HOOD SHOULD NEVER BE MORE THAN 72" ABOVE THE...

PRO LINE DUCT INFORMATION MODEL BLOWER (cfm) DUCT SIZE TRANSITION BS-PL30240 BS-PLIB600 6” BS-PL30240 BS-PLIB1200 10” BS-PL36240 BS-PLIB600 6” BS-PL36240 BS-PLIB1200 10” TR6X15/10 BS-PL42240 BS-PLIB600 6” BS-PL42240 BS-PLIB1200 10” TR6X15/10 BS-PL48240 BS-PLIB1200 10” TR6X15/10 BS-PL54240 BS-PLIB120...

INSTALLATION OF YOUR PRO LINE SERIES HOOD BLOWER INSTALLATION OF BS-PLIB600 INTERNAL BLOWER KIT REFER TO WIRING DIAGRAM 1. REMOVE SHIPPING BRACKET (SEE ITEM 1)FROM HOOD. DO NOT DISCARD SCREWS! 2. INSTALL BLOWER BRACKET WITH THE SCREWS REMOVED FROM THE SHIPPING BRACKET. 3. LOCATE THE TERMINAL BLOCK I...

INSTALLATION GUIDE FOR PRO LINE DUCT COVER LARGE HOLE FITS OVEREXISTING RIVET IN HOOD REMOVE RIVETS THATLINE UP WITH SMALLHOLES IN DUCT COVER SMALL HOLES USED FOR FASTENING OPTIONAL ATTACHMENT HOLES  REMOVE POP RIVETS FROM PRO HOOD THAT CORRESPOND WITH THE SMALL HOLES ON THE DUCT COVER.  INSTALL...

DIMENSIONS OF THE PYRAMID STYLE SERIES HOOD P/N 750306 Page 17

SITE PREPARATION FOR PYRAMID STYLE SERIES IN SELECTING THE PROPER HEIGHT TO MOUNT THE HOOD, TAKE INTO CONSIDERATION THE STATURE OF THE PERSON OR PERSONS WHO WILL BE COOKING. A HEIGHT OF 30", MINIMUM HEIGHT OFF OF COOKING SURFACE, TO 36" MAXIMUM HEIGHT OFF OF THE COOKING SURFACE, WILL SUIT MO...

THE CORRECT HEIGHT OF YOUR PYRAMID STYLE HOOD THE BOTTOM OF THE HOOD SHOULD BE 30" MINIMUM TO 36" MAXIMUM ABOVE THE COUNTERTOP. THIS WOULD TYPICALLY RESULT IN THE BOTTOM OF THE HOOD BEING 66" TO 72" ABOVE THE FLOOR. THE BOTTOM OF THE HOOD SHOULD NEVER BE MORE THAN 72" ABOVE THE F...

PYRAMID STYLE DUCT INFORMATION MODEL BLOWER (cfm) DUCT SIZE BS-PC30240 BS-PCIB600 6” BS-PC36240 BS-PCIB600 6” BS-PC36240 BS-PCIB1200 10” BS-PC42240 BS-PCIB600 6” BS-PC42240 BS-PCIB1200 10” BS-PC48240 BS-PCIB1200 10” BS-PC54240 BS-PCIB1200 10” BS-PC60240 BS-PCIB1200 10” BS-PC66240 BS-PCIB1200 10” IMP...

P/N 750306 Page 21 INSTALLATION OF YOUR PYRAMID STYLE HOOD BLOWER INSTALLATION OF BS-PCIB600 INTERNAL BLOWER KIT REFER TO WIRING DIAGRAM 1. REMOVE SHIPPING BRACKET(SEE ITEM 1) FROM HOOD. DO NOT DISCARD SCREWS! 2. INSTALL BLOWER BRACKET WITH THE SCREWS REMOVED FROM THE SHIPPING BRACKET. 3. LOCATE THE...

INSTALLATION GUIDE FOR FLUE (PYRAMID STYLE HOOD) 1. MEASURE FROM TOP OF THE CANOPY TO CEILING AND SUBTRACT 1/8" FOR CLEAR- ANCE. 2. PLACE THE DUCT COVER TOP INSIDE THE DUCT COVER BASE AND LOWER UNTIL DE- SIRED HEIGHT IS FOUND. (TO ELIMINATE SCRATCHES, MAKE A MARK ON THE DUCT COVER TOP FOR THE DE...

DIMENSIONS OF THE LOW PROFILE SERIES HOOD  INLET LOCATION FOR THE ELECTRICAL CONNECTION IS LOCATED ON TOP FOR STANDARD TOP EXHAUST AND ON REAR FOR OPTIONAL REAR EXHAUST. (SEE DETAIL BELOW)  ELECTRICAL REQUIREMENTS: 15 AMPS AT 120 VOLTS  LIGHT BULBS ARE HALOGEN G9, 120V, 25W  BULBS ARE OPERAT...

IN SELECTING THE PROPER HEIGHT TO MOUNT THE HOOD, TAKE INTO CONSIDERATION THE STATURE OF THE PERSON OR PERSONS WHO WILL BE COOKING. A HEIGHT OF 30", MINIMUM HEIGHT OFF OF COOKING SURFACE, TO 36" MAXIMUM HEIGHT OFF OF THE COOKING SURFACE, WILL SUIT MOST USERS. IF MOUNTED AT A HEIGHT GREATER T...

THE CORRECT HEIGHT OF YOUR LOW PROFILE SERIES THE BOTTOM OF THE HOOD SHOULD BE 30" MINIMUM TO 36" MAXIMUM ABOVE THE COUNTERTOP. THIS WOULD TYPICALLY RESULT IN THE BOTTOM OF THE HOOD BEING 66" TO 72" ABOVE THE FLOOR. THE BOTTOM OF THE HOOD SHOULD NEVER BE MORE THAN 72" ABOVE THE F...

LOW PROFILE DUCT INFORMATION TRC8/6 TRANSITION IS AVAILABLE TO INCREASE THE DUCT SIZE TO 8” FOR OPTIMAL PERFORMANCE IMPORTANT PLANNING INFORMATION! PROPER INSTALLATION OF DUCTING IS EXTREMELY INPORTANT FOR OPTIMAL PERFORMANCE OF YOUR BLUESTAR VENTILLATION SYSTEM.  ALL CFM’S ARE BASED ON TESTS AT 0...

DIMENSIONS OF THE RE-CIRCULATING HOOD  INLET LOCATION FOR THE ELECTRICAL CONNECTION IS LOCATED ON TOP OR REAR. (SEE DETAIL BELOW)  ELECTRICAL REQUIREMENTS: 15 AMPS AT 120 VOLTS  LIGHT BULBS ARE HALOGEN G9, 120V, 25W  BULBS ARE OPERATED BY A DIMMER SWITCH  BLOWER IS VARIABLE SPEED P/N 75030...

IN SELECTING THE PROPER HEIGHT TO MOUNT THE HOOD, TAKE INTO CONSIDERATION THE STATURE OF THE PERSON OR PERSONS WHO WILL BE COOKING. A HEIGHT OF 30", MINIMUM HEIGHT OFF OF COOKING SURFACE, TO 36" MAXIMUM HEIGHT OFF OF THE COOKING SURFACE, WILL SUIT MOST USERS. IF MOUNTED AT A HEIGHT GREATER T...

THE CORRECT HEIGHT OF YOUR RE-CIRCULATING HOOD THE BOTTOM OF THE HOOD SHOULD BE 30" MINIMUM TO 36" MAXIMUM ABOVE THE COUNTERTOP. THIS WOULD TYPICALLY RESULT IN THE BOTTOM OF THE HOOD BEING 66" TO 72" ABOVE THE FLOOR. THE BOTTOM OF THE HOOD SHOULD NEVER BE MORE THAN 72" ABOVE THE ...

CLEANING AND MAINTENANCE YOUR HOOD MUST BE KEPT CLEAN AND MAINTAINED PROPERLY!! BAFFLE FILTERS  BAFFLE FILTERS SHOULD BE EXAMINED PERIODICALLY TO ASSURE THAT ALL SUR-FACES AND PARTS ARE CLEAN  THE FILTERS ARE DISHWASHER SAFE OR IN A SINK WITH HOT, SOAPY WATER  EASY PERIODIC CLEANING WILL ASSUR...

WHAT IS COVERED? Prizer-Painter provides the following limited warranties to the original retail purchasers of Products sold and installed in the continental United States and Canada on or after February 22, 2002: Initial Seven (7) Day Limited Warranty. Prizer-Painter warrants that all cosmetic comp...

WHAT IS NOT COVERED? This Limited Warranty is the sole and exclusive warranty provided for the Product and extends only to original retail purchasers in the continental United States and Canada. This Limited Warranty is not trans-ferable to any subsequent purchasers or users. If any implied warranti...

This checklist has been developed to assure proper installation of your appliance To validate your warranty you must mail or fax this form and a copy of your receipt to: Warranty Department, Prizer-Painter, 600 Arlington Street, Reading, PA 19611, Fax (610) 376-2596 Customer Information (Please Prin...