Page 2 - ) SELECTION OF POOL SITE; GENERAL INFORMATION
Do not start the installation of your pool unless you hav e an entire day to finish the work.Do not try to set up your pool on a windy day.The wall will be difficult or even impossible to handle. An average pool needs 2 or 3 people for installation.The following tools and materials are needed. Shove...
Page 3 - ) GROUND PREPARATION
23 ' 8 -1/ 4" (4 8" W a ll ) 24 ' 1/ 4" (5 2" W a ll ) a) Mark off your pool area by driving stakes. Have a helper hold a tape measure or a string and mark off the pool perimeter using flour or chalk. Remov e sod inside the pool area to a distanceof 1 feet beyond dimensions shown in ...
Page 4 - ST; t Met
3 Us e #0 104 P A C K O v al f ram e bol t pack a ge. Us e #0 105 (#010 6) P A C K S tr ap b ol t p ac k age . 3 ) A SSEM B L IN G SI D E VER T IC A L , H O R IZ O N T A L SU PPO R T A N D B R A C E 1/ 4" x 1/ 2 " T ru s s Hea d S c rew P .No. 3 313 S ide V ert ic al F o r 4 8" P .No. 3 ...
Page 6 - ) DRAWING POOL SHAPE; Please Draw a line with seeing the picture of each pool size.
4) DRAWING POOL SHAPE Please Draw a line with seeing the picture of each pool size. (618mm) 2' 3/8" (1806m m ) 5' 11- 1/ 8" 5' 7-5/ 8 " (4847mm) 16x12 5 ' 11- 1/8" 2' 3/8" (3611 m m ) (618mm) 11' 10 -1 /8" (1236mm) (1717 m m ) 15' 10-7/8" (1806m m ) 4' 5/8" (7319mm) 2...
Page 7 - Do not fill back hole at this point.
5" IMPORTANT:See "7) POSITIONING ASSEMBLED OVAL PARTS." Do not fill back hole at this point. Digging holes;Dig holes for each horizontal support as shown right. inside of pool from "X" point 12 1/2" length. Dig holes where center of patio blocks can be placed at 40" from ...
Page 8 - ) POSITIONING ASSEMBLED OVAL PARTS; End strap; ) CONNECTING TENSION STRAPS; Middle strap
7 P.No.0923 P.No.0923 M8 x 20 Hex Head Bolt M8 x 20 Hex Head Bolt P.No.0623 P.No.0623M8 Nut M8 Nut Top seat temporally placed should be removed beforeproceeding to next step. Note:All Bolts to be inserted from the top side, Nuts to be inserted from undernerath Tension straps. 6) POSITIONING ASSEMBLE...
Page 9 - ) ASSEMBLING BOTTOM RAIL
Bring the wall close to the bottom rail.Make sure there is nothing in the bottom rail before inserting the wall. If there is earth or something is in the bottom rail,take out it accordingly.Begin to insert end of wall into bottom rail. One person unwinding wall (wall should be on a plywood base for ...
Page 10 - 2) FILLING THE POOL
DO NOT FASTEN THE W ALL W ITHOUT USING THE REINFORCINGW ASHERS ! FAILURE TO USE REINFORCING W ASHERS AS INSTRUCTED W ILL CAUSE W ALL TO SPLIT W HEN POOL IS FILLED. THIS CAN CAUSE SERIOUS PROPERTY DAMAGE AND/OR BODILYINJURY. INSERT THE SCREW S FROM INSIDE OF W ALL.NUT MUST BE FASTENED FROM OUTSIDE OF...
Page 11 - 3) HELPFUL INFORMATION; NOT THE MANUFACTURER.; READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING YOUR POOL.; WARNING; PERMANET INJURY OR DEATH CAN RESULT.; DANGER; DO NOT; JUMP
Leaks in skimmer and filter connections must be stopped.A constant drip of chlorinated water on metal will corrode the metal. a) Proper filtering and chemical treatments should not make it necessaryto change the pool water.Your pool dealer will adv ise you of the proper procedure.To estimate the amo...
Page 12 - BRACED OVAL PARTS LIST
BRACED OVAL PARTS LIST RG11-A (48") CARTON Parts No. Discription 16x12x48 20x12x48 24x12x48 25x15x48 30x15x48 33x18x48 41x21x48 3313 Side Vertical (48" Wall) 2 4 6 4 6 6 8 4105 Brace (For 48" Wall) 2 4 6 4 6 6 8 5238 Horizontal Support (48" Wall) 2 4 6 4 6 6 8 6254 Pressure plate L=6...
