Black Box SWI082 - Manuals

Black Box SWI082 – Manual in PDF format online.

Manuals:

Manual

Manual Black Box SWI082

Summary

Page 5 - NOM STATEMENT

3 NOM STATEMENT 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos,poniendo particular aten...

Page 6 - DUAL-PORT NETWORK POWER SWITCH; TRADEMARKS USED IN THIS MANUAL

4 DUAL-PORT NETWORK POWER SWITCH TRADEMARKS USED IN THIS MANUAL AT ® is a registered trademark of International Business Machines Corporation. Crosstalk ® is a registered trademark of Digital Communications Associates, Inc. ProComm ® is a registered trademark of DATASTORM TECHNOLOGIES, INC.™ UNIX ® ...

Page 7 - WARNINGS AND CAUTIONS; WARNING; CAUTION

5 WARNINGS AND CAUTIONS WARNING There are no serviceable parts inside the Dual-Port Network PowerSwitch! Do NOT attempt to repair or service this device yourself. YOUM I G H T B E S H O C K E D ! I n t e r n a l c o m p o n e n t s m u s t b e s e r v i c e d b yauthorized personnel only. This devic...

Page 9 - CONTENTS; Contents; Chapter

7 CONTENTS Contents Chapter Page 1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102.1 Description . . . . . . ....

Page 11 - CHAPTER 1: Specifications; Operating Temperature:

9 CHAPTER 1: Specifications 1. Specifications Coding: Serial ASCII, 8 bits, No parity Speed: 2400 bps, 9600 bps, 19.2 kbps, 38.4 kbps Indicators: (7) LEDs: ON, RDY, RXD, DCD, NET, Outlet ON 1, Outlet ON 2 Connectors: (1) DB9 male modem; (1) DB9 male RS-232 console; (1) RJ-45 female 10BASE-T Ethernet...

Page 13 - CHAPTER 2: Introduction; NOTE

11 CHAPTER 2: Introduction 2.3 Front Panel As shown in Figure 2-1, the Dual-Port Network Power Switch front panel includes aseries of LED indicators. Descriptions of the LEDs are listed below. Figure 2-1. Front panel. 1. ON: Lights when AC power is applied to the Dual-Port Network Power Switch. 2. R...

Page 15 - CHAPTER 3: Installation

13 CHAPTER 3: Installation 3. Installation 3.1 Option Switches The option switches select default settings for the baud rate, command echo, bootdelay, and disconnect timeout. Default settings selected via the option switches willbe used when the unit is reset to default parameters as described in Se...

Page 16 - Switch; Console Port Connection; Connecting an External Modem; Connecting the Network Cable

14 DUAL-PORT NETWORK POWER SWITCH Table 3-1. Option switch settings. Switch Function Up Down 1 Default baud rate 38.4 kbps 9600 bps* 2 Default boot delay 10 seconds 5 seconds* 3 Default command echo Enable Disable* 4 Default disconnect timeout 30 minutes 2 minutes* *Default setting. 3.2 Console Port...

Page 17 - Connection to Switched Outlets

15 CHAPTER 3: Installation 3.5 Power Supply Connection Connect the Dual-Port Network Power Switch to an appropriate power supply. CAUTION This device should only be operated with the type of power sourceindicated on the instrument nameplate. If you are not sure of the type ofpower service available,...

Page 19 - System Mode and User Mode

17 CHAPTER 4: Startup/Configuration 4. Startup/Configuration 4.1 System Mode and User Mode To restrict access to sensitive command functions, the Dual-Port Network PowerSwitch features two separate operating modes: system mode and user mode. The system mode allows access to all configuration menus, ...

Page 26 - NOTES; Network Parameters

24 DUAL-PORT NETWORK POWER SWITCH NOTES If you want to allow a single user to access both switched plugs, assignthe same user password to both plugs. If you want to “split” plug access between two different users (eachuser controls their own plug), then assign a different user password toeach plug. ...

Page 27 - IP S

25 CHAPTER 4: Startup/Configuration Figure 4-5. Network Parameters menu (system mode only). The following options are available: 1. IP Address: Defines the IP address for the Dual-Port Network Power Switch. Type 1 , press [Enter], and follow the instructions in the submenu. (Default = undefined.) 2....

Page 29 - Save Configuration Parameters

27 CHAPTER 4: Startup/Configuration Example 2: Allow access only by addresses that begin with 192. Security Mask #1: 255.255.255.255 Mask #1 Action: DenySecurity Mask #2: 192.255.255.255 Mask #2 Action: Permit Since 255 is a wild card, Mask 1 blocks all IP addresses. Mask 2 then grants access toall ...

Page 31 - Displaying Plug Status

29 CHAPTER 5: Operation 5.2 Displaying Plug Status The Status screen displays the on/off state and selected parameters for theswitched plugs. To display the Status screen, type /S and press [Enter]. NOTE Although the /S command is available in both user and system mode,the System Status screen inclu...

Page 34 - The Default Command; The Automated Mode

32 DUAL-PORT NETWORK POWER SWITCH 2. Both plugs: To apply a command to both owned plugs, enter an asterisk in place of the name or number. For example: /ON * or /BO * 5.4 The Default Command The default command (/D) sets plugs to their default on/off status. The defaultstatus is set using the Plug P...

Page 38 - Saving and Restoring; Sending Parameters to a File; Restoring Saved Parameters

36 DUAL-PORT NETWORK POWER SWITCH 6. Saving and Restoring Configuration Parameters After the Dual-Port Network Power Switch has been properly configured,parameters can be downloaded and saved as an ASCII text file. Later, if theconfiguration is accidentally altered, the file with the saved parameter...

Page 39 - CHAPTER 6: Saving and Restoring Configuration Parameters; and press [Enter]. The Switch will display the status screen with

37 CHAPTER 6: Saving and Restoring Configuration Parameters 2. Configure your communications program to upload an ASCII text file. 3. Upload the file with the saved parameters. If necessary, key in the file name and directory path. 4. When the upload is complete, make certain to terminate the commun...

Page 40 - Appendix A. Interface Descriptions; A.1 Console Port Interface

38 DUAL-PORT NETWORK POWER SWITCH Appendix A. Interface Descriptions A.1 Console Port Interface Figure A-1. Console port interface. A.2 Modem Port Interface Figure A-2. Modem port interface.

Page 41 - APPENDIX B: Optional Mounting Bracket Instructions; Rackmounting Bracket Instructions

39 APPENDIX B: Optional Mounting Bracket Instructions Appendix B. Optional Rackmounting Bracket Instructions The Dual-Port Network Power Switch can either be placed on a desktop, installedin a 19" equipment rack, or mounted on a wall. This appendix describes theprocedures for installing the opti...

Page 43 - APPENDIX C: Troubleshooting; Appendix C. Troubleshooting; C.1 Calling Black Box; C.2 Shipping and Packaging

41 APPENDIX C: Troubleshooting Appendix C. Troubleshooting C.1 Calling Black Box If you determine that your Dual-Port Network Power Switch is malfunctioning, donot attempt to alter or repair the unit. It contains no user-serviceable parts.Contact Black Box at 724-746-5500. Before you do, make a reco...