Black Box SW591C - Manuals

Black Box SW591C – Manual in PDF format online.

Manuals:

Manual

Manual Black Box SW591C

Summary

Page 2 - CODE OPERATED SWITCH II

FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to r...

Page 3 - Operation; NOTE; Contents

Chapter Page 1 Specifications .............................................................................................................4 2 Introduction ...............................................................................................................5 3 Installation....................

Page 5 - CHAPTER 2: Introduction

The Code Operated Switch II (COS II) makes code-operated switching possible for diversecombinations of serial devices. As it switches, theCOS II also reconciles differences in word size,speed, flow control, and parity for up to fourdevices. An Expansion Board, available separately,doubles the maximu...

Page 7 - NOTE: Every time you change the DIP switch; Appendix; Functions and Arrangement of the Switch; CHAPTER 3: Installation

The board layout for the Four-Port Expansion Board is shown on this page (Fig. 2). If you haveordered one, check your Board to make sure itmatches. NOTE: Every time you change the DIP switch settings, you must press the reset buttonlocated on the front panel of the switch, orunplug the power supply....

Page 8 - Configuring Ports with the Individual Port; SWF; Responsibility for the Link Command; NOTE: If the slave ports are set up for hardware

In addition, there are some system characteristicsthat are set with the eighth DIP switch of theindividual port switch banks. Sections 3.6 and 3.7 explain these functions in depth. 3.4 Bank Assignments The individual port switch banks are assigned asfollows: Bank Label Port SWA Master Device Port SW...

Page 9 - Graphics Pause; NOTE: If the internal buffer fills, the appropriate; always asserted. They are

Automatic Timeout The COS II times the intervals between thereception of each character and the next. You mayinstruct it to return to an unlinked state afterintervals of 2.5, 5, or 10 minutes, or you may disablethis automatic timeout feature. SWF 5 and SWF 6control this feature. control lead (DTR or...

Page 10 - SWG

3.6.2 S ETTING THE A RMING C HARACTER WITH SWG Switch Bank SWG supplies a portion of the control-code sequence, the sequence that activates the Switch.The arming character, the ASCII code that alerts the COS-II to an upcoming switch action, is set with SWG.The settings are given in the chart below. ...

Page 15 - We recommend that you run software; For Set; Normal operation; Sending or Suppressing Breaks

ARMING CHARACTER SWITCH POSITIONS LSB MSB ASCII CTRL HEX DECIMAL 1 2 3 4 5 6 7 8 DF 223 ON ON ON ON ON OFF ON ON E0 224 OFF OFF OFF OFF OFF ON ON ON E1 225 ON OFF OFF OFF OFF ON ON ON E2 226 OFF ON OFF OFF OFF ON ON ON E3 227 ON ON OFF OFF OFF ON ON ON E4 228 OFF OFF ON OFF OFF ON ON ON E5 229 ON OF...

Page 16 - Text; A shunt jumper lies in each shunt marked DCE.

To Set SWB 8 Pass breaks ON Ignore breaks OFF Lead Pass-Through This function allows the COS II either to passhardware-handshake leads to connected devices, orto block them. If they are blocked, the leads will stillbe used to regulate the 8K internal buffer of theSwitch. The following table shows th...

Page 17 - Chapter 4; explains these

3.9. Connecting and Powering Up the COS-II Once you have configured the internal switches andjumpers, you can connect your devices and thewallmounted power jack to the COS-II. Before youbegin, you might wish to check the settings of allthe DIP switches again, to make sure you have setthem correctly....

Page 18 - Chapter 3

4.1. Introduction The primary action of the Switch consists ofdetecting and responding to control-codesequences. As it switches to a particular port, theCOS-II establishes a link between the master andthe slave device. After the COS-II has switched, itcan lock the link out, that is, it can ignore al...

Page 20 - After you have hit a key, the screen will change to:

CODE OPERATED SWITCH II After you have hit a key, the screen will change to: Serial Port Test The Serial Port Test is a loopback test that checkswhether data is being correctly transmitted andreceived on any port. The test also checks, usingDTR/CTS/RI or RTS/DCD, whether the box canloop back control...

Page 21 - Quick Reference Guide

Individual Port Switch Bank Settings Switch Position Setting Option 1 2 3 4 5 6 7 Speed 110 bps ON ON ON 300 bps OFF ON ON 600 bps ON OFF ON 1200 bps OFF OFF ON 2400 bps ON ON OFF 4800 bps OFF ON OFF 9600 bps ON OFF OFF 19200 bps OFF OFF OFF Parity none OFF OFF even OFF ON odd ON OFF Word Size 7 bit...

Page 22 - System Switch Options Available through Position 8; Text Mode

System Switch Options Available through Position 8 Switch Option SWA 8 SWB 8 SWC 8 SWD 8 SWE 8 Self-test ON Normal operation OFF Pass breaks ON Ignore breaks OFF Lead pass-through ON Normal operation OFF Graphics ModePause In Master Data ON ON Slave Data OFF ON Master or slave data ON OFF Text Mode ...