Black Box AC455A-TX-R2 - Manuals

Page 4 - FIBER LINK

3 FIBER LINK 12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo no sea eliminada. 13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni pellizcados por objetos colocados sobre o contra ellos,poniendo particular atenció...

Page 5 - TRADEMARKS USED IN THIS MANUAL

4 FIBER LINK TRADEMARKS USED IN THIS MANUAL Any trademarks mentioned in this manual are acknowledged to be the property ofthe trademark owners.

Page 6 - Contents

5 FIBER LINK Contents 1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.1 Description . . . . . . . . . . . . . . . . . . . . . . . ....

Page 10 - NOTE; Environmental

9 FIBER LINK Electrical Input Voltage —AC455A-TX-R2: 12 to 16 VAC, 12 to 14 VDC; AC456A-RX-R2: 13.5 to 16 VDC Input Power Frequency —50 to 60 Hz Current Requirement —AC455A-TX-R2: 300 mA; AC456A-RX-R2: 380 mA Power Consumption —6 W Heat Equivalent —0.3 BTU/min., 0.09 cal/min. NOTE The heat equivalen...

Page 11 - Additional Features

10 FIBER LINK 2. Introduction 2.1 Description The Fiber Link supports the transmission of video from a camera to a monitoringstation and a data signal back to the camera over one multimode fiber. A singlecoaxial cable at each end of the link is used to connect the appropriate equipmentto the system....

Page 13 - CAUTION

12 FIBER LINK 3. Installation To install the Fiber Link, you will physically install the modules, connect theoptical fiber, connect the input and output electrical signals, and connect power tothe fiberoptic modules. Then you’ll verify correct system operation. 3.1 Physical Installation The Fiber Li...

Page 15 - Optical Connections; Function

14 FIBER LINK NOTE Use RG59/U coaxial cable (part number ETN59-BNC) between the videoequipment and the fiber units. The video equipment and the fiber unitshould be no more than 100 ft. (30.5 m) apart. Terminate the coaxial cable with a female BNC and connect it to the fiber unit. Repeat for both end...

Page 16 - POWER

15 FIBER LINK Figure 3-2. Electrical Connection. 4. Seat the connector in its position in the fiber unit. 5. Plug the power supply into a suitable outlet. 3.5 System Power Power up the peripheral equipment. You’ll need to verify system operation. Youcan do this by observing video on the monitor at t...

Page 17 - Transmitter and Receiver Optical; Indicator

16 FIBER LINK 4. Transmitter and Receiver Optical Indicators All transmitters and receivers have five active LEDs. See Figure 4-1 . Level/Loss indicators are used in determining received optical power. The LED will glow in varying intensities of green depending upon the amount of opticalpower receiv...

Page 20 - Calling Black Box

19 FIBER LINK 5. Troubleshooting 5.1 Try This First If you encounter problems using the Fiber Link: 1. Check to make sure the power is properly connected to the modules. 2. Then verify that the fiber is good. 3. Check the video status indicators. If they’re lit, power and video are present. NOTE Eve...