BILLY GOAT VQ1002SP - Manuals

Page 2 - VIBRATION LEVEL 1.9 g; SOUND; TABLE OF CONTENTS; IN THE INTEREST OF SAFETY; The Engine Exhaust from this product contains chemicals known; Sound level of 88 dBA at operator position

Part No. 830542 Form No. F021302G Vibration levels at the operators handles weremeasured in the vertical, lateral, and longitudinaldirections using calibrated vibration test equipment.Tests were performed on 07/02/97 under theconditions listed: VIBRATION LEVEL 1.9 g SOUND Page 2 of 16 7 8 VIBRATION ...

Page 3 - DANGER; CONTROLS; INSTRUCTION LABELS; Stop; Start; OIL ALERT; ENGINE LABELS; Honda; PULL TO ENGAGE CLUTCH

Part No. 830542 Form No. F021302G EXPLOSIVE FUEL STOP ENGINE AND ALLOW T OCOOL BEFORE REFUELING. 400268 WARNING DANGER 810736 890254 These labels should be included on your Vacuum. If any of these labels are damaged, replace them before putting thisequipment into operation. Item and part numbers are...

Page 4 - QUICK DISCONNECT; GENERAL SAFETY; PACKING CHECKLIST; Boxing Checklist; Per Model; Main Unit; Upper Handle

Part No. 830542 Form No. F021302G Page 4 of 16 For your safety and the safety of others, these directions should be followed: Use of Ear Protection is recommended whileoperating this machine. Do not operate this machine without first readingowner's manual and engine manufacturer's manual. Use of Eye...

Page 5 - PUT OIL IN ENGINE BEFORE STARTING.; ASSEMBLY; NOZZLE DOOR CONTROLS.; SELF PROPELLED ONLY; Check tire pressure and lubricate all grease and oil points; Deflector

Part No. 830542 Form No. F021302G N Page 5 of 16 PUT OIL IN ENGINE BEFORE STARTING. Read all safety and operating instructionsbefore assembling or starting this unit. ASSEMBLY 10 Your Billy Goat is shipped from the factory in one carton, com-pletely assembled except for the debris bag, deflector ass...

Page 6 - OPERATION; djust nozzle close to debris,; NOZZLE GOBBLER DOOR; Frequently empty debris to prevent bag overloading with; DO NOT place bag on or near hot surface; (see Safety Warnings; DEBRIS BAG; STARTING; VACUUMING OPERATION; VACUUM NOZZLE HEIGHT ADJUSTMENT:

Part No. 830542 Form No. F021302G Page 6 of 16 16 OPERATION FOR MAXIMUM PICKUP: A djust nozzle close to debris, but without blocking airflow into the nozzle. NOTE : Never bury nozzle into debris. CLEARING A CLOGGED NOZZLE& EXHAUST: Turn engine off and wait for impeller to stop completely and dis...

Page 7 - continued; PROPULSION; VQ self-propelled vacuums are equipped with; Throttle; Position Rev. N 1 2 3 4 5

Part No. 830542 Form No. F021302G Page 7 of 16 16 OPERATION continued PROPULSION 16.6 PROPULSION: VQ self-propelled vacuums are equipped with 5 forward gears, neutral and reverse. With the engine running,the bail in released position and brake in on position, selectdesired drive gear. Pull bail agai...

Page 8 - PARTS DRAWING

Part No. 830542 Form No. F021302G Page 8 of 16 18 PARTS DRAWING VQ802SPH, VQ1002SP

Page 12 - Cable Ass'y Switch VQ; Switch & Wire Assembly Parts List; Black

Part No. 830542 Form No. F021302G PARTS LIST 1 0 7 Switch Toggle 6A/125V 830239 1 108 Cable Ass'y Switch Ground 400278 1 109 Cable Ass'y Switch VQ 830278 1 110 Connector-Tap in Squeeze 810673 1 E-1 Wire to Engine Stop Switch ---- -- Switch & Wire Assembly Parts List (Honda SP only) 19 Page 12 of...

Page 13 - STORAGE; See; Curb Guide

Part No. 830542 Form No. F021302G Page 13 of 16 16 OPERATION continued Do not lift by hand. Use loading ramps or other mechanical assis-tance. Secure in place during transport. 16.4 HANDLING & TRANSPORTING: Never store engine indoors or in enclosed poorly venti- lated areas with fuel in tank, wh...

Page 14 - MAINTENANCE; ENGINE; Inspect; IMPELLER REMOVAL; Using a penetrating oil can

Part No. 830542 Form No. F021302G Page 14 of 16 MAINTENANCE Use only a qualified mechanic forany adjustments, disassembly orany kind of repair . DISCONNECT SPARK PLUG WIREBEFORE SERVICING UNIT. WARNING: TO AVOID PERSONAL INJURY, ALWAYSTURN MACHINE OFF, MAKE SURE ALL MOVINGPARTS COME TO A COMPLETE ST...

Page 15 - DO NOT OVER ADJUST; Maintenance Schedule; Maintenance Operation; Check for excessive vibration

Part No. 830542 Form No. F021302G 0.125 (3.3mm) 0.06 (1.5mm) ENGAGED DRIVE POSITON: WIRE BELT GUIDES SHOULD CLEAR BELT BY 0.06" - 0.125"(1.5mm - 3.3mm) Page 15 of 16 Fig. 11 MAINTENANCE continued 17 CHAIN ADJUSTMENTS (see figure 9) 1. Remove guards.2. Inspect chain and sprockets for wear, lu...

Page 16 - TROUBLESHOOTING; Before Requesting Service Review These Suggestions; Possible Cause; Engine Service and Warranty; Contact your nearest engine manufacturer's authorized; Serial Plate; WARRANTY PROCEDURE

Part No. 830542 Form No. F021302G Page 16 of 16 Solution Problem TROUBLESHOOTING Before Requesting Service Review These Suggestions 20 Self propelled drive will not release Will not vacuum or has poor vacuumperformance. Dirty debris bag. Nozzle height set too high ortoo low. Nozzle gobbler door not ...