BILLY GOAT TKD512SP - Manuals

Page 2 - Part No. 890604 Form No. F021602C; IN THE INTEREST OF SAFETY; DO NOT transport unit with fuel in tank.; fins because contact may cause burns.; VIBRATION; SOUND; TABLE OF CONTENTS; The Engine Exhaust from this product contains chemicals known

Part No. 890604 Form No. F021602C Page 2 of 12 IN THE INTEREST OF SAFETY THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTYDAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL &ENGINE MANU...

Page 3 - Part No. 890604 Form No. F021602C; PUT OIL IN ENGINE BEFORE STARTING; ASSEMBLY; Tamper; QUICK DISCONNECT; Literature Assy; Debris Bag

Part No. 890604 Form No. F021602C Page 3 of 12 PUT OIL IN ENGINE BEFORE STARTING Read all safety and operating instructionsbefore assembling or starting this unit. 890028 TKD Check These items should be included in your carton. Ifany of these parts are missing, contact your dealer. ASSEMBLY PACKING ...

Page 4 - Manual; Literature Checklist; CONTROLS; INSTRUCTION LABELS; Start; WARNING

Part No. 890604 Form No. F021602C Page 4 of 12 Owner's Manual Literature KD / TKD Accessories Check Owner's Manual 890604 Literature KD / TKD Accessories 890409 Check Literature Checklist Check EU Declaration of Conformity & EU Distributor List 890393 EU Declaration of Conformity & EU Distri...

Page 5 - VACUUM NOZZLE HEIGHT ADJUSTMENT:; is; PUT OIL IN ENGINE BEFORE STARTING.; OPERATION; STARTING; VACUUMING OPERATION; Use caution when using chipper; Your; TERMITE; chipper is designed to process tree branches; CLEARING A CLOGGED CHIPPER HOPPER (TKD ONLY); Under normal circumstances, allow time for machine; CHIPPING OPERATION; Maximum

Part No. 890604 Form No. F021602C Page 5 of 12 VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle andpulling height adjust rod (item 23) up at left rear of machine. FOR MAXIMUM PICKUP: A djust nozzle close to debris, but without blocking airflow into the nozz...

Page 6 - continued; more weight than you can lift.; DO NOT place bag on or near hot surface, such as engine.; Run; Run machine at idle to quarter throttle.; DO NOT leave debris in bag while in storage.; DEBRIS BAG

Part No. 890604 Form No. F021602C Page 6 of 12 OPERATION continued 16 Note: Frequently empty debris to prevent bag overloading with more weight than you can lift. An optional bag and dust cover is available for use where debris will bevacuumed in dusty conditions (see Optional Accessories shown onpa...

Page 7 - Never store engine indoors or in enclosed poorly ventilated; Do not store with debris in bag.; STORAGE; Tamper Storage Position; PROPULSION

Part No. 890604 Form No. F021602C Page 7 of 12 Before turning machine off, use the Tamper to slowly pushremaining pieces of wood through the chipper. This canprevent any remaining wood from jamming in the chipper whenmachine is turned off.Do not leave tamper on the ground, store tamper in the chippe...

Page 8 - MAINTENANCE; CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY; shim washer must be used.; Chipper blades are normal replaceable wear items.; Chipper blade is sharp.; Be careful to avoid heat buildup; Chipper blade installation is in reverse order of removal.; INCORRECT; your unit may or may not have required the use of shim; EDGE OF CHIP; IMPELLER REMOVAL and CHIPPER ADJUSTMENT; Wait for engine to cool and disconnect spark plug.; IMPELLER REMOVAL

Part No. 890604 Form No. F021602C Page 8 of 12 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY Depending on the type and amount of wood being chipped, thechipper blade will eventually get dull, losing it’s cutting ability.Evidence of a dull blade is a noticeably reduced chipping ability or...

Page 9 - Maintenance Operation; Maintenance Schedule; Carriage; CLUTCH ADJUSTMENT; DRIVE; CHAIN REPLACEMENT

Part No. 890604 Form No. F021602C Page 9 of 12 MAINTENANCE continued IMPELLER REMOVAL continued 18. If chipper blade properly clears anvil surface, proceed to step .If not, return to (step 14) and add or subtract shim washers asneeded to obtain a correct gap. 19. Reinstall engine and impeller onto h...

Page 10 - PARTS DRAWING

Part No. 890604 Form No. F021602C Page 10 of 12 18 PARTS DRAWING KD512SP, TKD512SP

Page 12 - Engine Service and Warranty; Contact your nearest engine manufacturer's authorized; WARRANTY PROCEDURE; Serial Plate; TROUBLESHOOTING; Before Requesting Service Review These Suggestions; PARTS LIST

Part No. 890604 Form No. F021602C Page 12 of 12 Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 22.1 22 BILLY GOAT INDUSTRIES INC. 1803 S.W. Jefferson Street Lee's Summit, MO 64082 / USAPHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com WARRAN...