BILLY GOAT KD511SP, TKD511SP - Manuals

Page 2 - Par t No. 890034 Form No. F101000A; IN THE INTEREST OF SAFETY; VIBRATION; SOUND TESTS; SOUND; The Engine Exhaust from this product contains chemicals known

Par t No. 890034 Form No. F101000A Page 2 of 12 IN THE INTEREST OF SAFETY THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTYDAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL &ENGINE MAN...

Page 3 - ASSEMBLY; Tamper; ASSEMBLE; the debris bag (item 1) and fasten bag neck to bag quick; ATTACH; Literature Assy; Connector

Par t No. 890034 Form No. F101000A Page 3 of 12 PUT OIL IN ENGINE BEFORE STARTING Read all safety and operating instructionsbefore assembling or starting this unit. Debris Bag890022 KD890028 TKD Check These items should be included in your carton. If anyof these parts are missing, contact your deale...

Page 4 - Manual; Literature Checklist; CONTROLS; INSTRUCTION LABELS; Start; WARNING; D A N G E R; DANGER

Par t No. 890034 Form No. F101000A Page 4 of 12 Owner's Manual Literature KD / TKD Accesso- ries Check Owner's Manual 890034 Literature KD / TKD Accesso- ries 890409 Check Literature Checklist Check EU Declaration of Conformity & EU Distributor List 890393 EU Declaration of Conformity & EU D...

Page 5 - VACUUM NOZZLE HEIGHT ADJUSTMENT:; Danger; IF YOUR UNIT FAILS TO START:; OPERATION; STARTING; VACUUMING OPERATION; Use caution when using chipper; TERMITE; CLEARING A CLOGGED CHIPPER HOPPER-TKD ONLY; Under normal circumstances, allow time for machine; CHIPPING OPERATION; Maximum

Par t No. 890034 Form No. F101000A Page 5 of 12 VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle andpulling height adjust rod (item 23) up at left rear of machine. FOR MAXIMUM PICKUP: A djust nozzle close to debris, but without blocking airflow into the noz...

Page 6 - Frequently empty debris to prevent bag overloading with; (see Optional Accessories shown on; DO NOT place bag on or near hot surface; Run; (see Safety Warnings; DO NOT; DEBRIS BAG

Par t No. 890034 Form No. F101000A Page 6 of 12 OPERATION continued 16 Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.An optional bag and dust cover is available for use where debris will bevacuumed in dusty conditions (see Optional Accessories shown on p...

Page 7 - Never store engine indoors or in enclosed poorly ventilated; Do not store with debris in bag.; continued; STORAGE; Tamper Storage Position; can be varied by applying slight downward; PROPULSION

Par t No. 890034 Form No. F101000A Page 7 of 12 Before turning machine off, use the Tamper to slowly pushremaining pieces of wood through the chipper. This canprevent any remaining wood from jamming in the chipper whenmachine is turned off.Do not leave tamper on the ground, store tamper in the chipp...

Page 8 - MAINTENANCE; CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY; The chipper blade gap is factory set and should be checked; INCORRECT; and

Par t No. 890034 Form No. F101000A Page 8 of 12 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY Depending on the type and amount of wood being chipped, thechipper blade will eventually get dull, losing it’s cutting ability.Evidence of a dull blade is a noticeably reduced chipping ability o...

Page 9 - IMPELLER REMOVAL; . If chipper blade properly clears anvil surface, proceed to step .; Maintenance Operation; Maintenance Schedule; Rod; CLUTCH ADJUSTMENT; DRIVE

Par t No. 890034 Form No. F101000A Page 9 of 12 MAINTENANCE continued IMPELLER REMOVAL continued 18 . If chipper blade properly clears anvil surface, proceed to step . If not, return to (step 14) and add or subtract shim washers asneeded to obtain a correct gap. 19. Reinstall engine and impeller ont...

Page 10 - PARTS DRAWING

Par t No. 890034 Form No. F101000A Page 10 of 12 18 PARTS DRAWING KD511SP, TKD511SP

Page 12 - Engine Service and Warranty; Contact your nearest engine manufacturer's authorized; WARRANTY PROCEDURE; Serial Plate; Model; TROUBLESHOOTING; Before Requesting Service Review These Suggestions; PARTS LIST

Par t No. 890034 Form No. F101000A Page 12 of 12 Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 22.1 22 BILLY GOAT INDUSTRIES INC. 1803 S.W. Jefferson Street Lee's Summit, MO 64082 / USAPHONE: 816-524-9666 FAX: 816-524-6983 WEBSITE: www.billygoat....