BILLY GOAT KD510SP, TKD510SP - Manuals

Page 2 - Part No. 890424 Form No. F011398A; IN THE INTEREST OF SAFETY; DO NOT transport unit with fuel in tank.; VIBRATION; SOUND; TABLE OF CONTENTS; The Engine Exhaust from this product contains chemicals known

Part No. 890424 Form No. F011398A Page 2 of 12 IN THE INTEREST OF SAFETY THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTYDAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY. BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL & EN-GINE MA...

Page 3 - PUT OIL IN ENGINE BEFORE STARTING; ASSEMBLY; PACKING CHECKLIST; GENERAL SAFETY; Tamper; QUICK DISCONNECT; Literature Assy; Connector

Part No. 890424 Form No. F011398A Page 3 of12 PUT OIL IN ENGINE BEFORE STARTING Read all safety and operating instructionsbefore assembling or starting this unit. Debris Bag890304 KD890306 TKD C h e c k These items should be included in your carton. Ifany of these parts are missing, contact your dea...

Page 4 - Manual; CONTROLS; D A N G E R; INSTRUCTION LABELS; DANGER; Start

Part No. 890424 Form No. F011398A Page 4 of 12 Owner's Manual Literature KD / TKD Accessories C h e c k Owner's Manual 890424 Literature KD / TKD Accessories 890409 C h e c k Literature Check-list C h e c k EU Declaration of Conformity & EU Distributor List 890393 EU Declaration of Conformity &a...

Page 5 - VACUUM NOZZLE HEIGHT ADJUSTMENT:; is; djust nozzle close to; PUT OIL IN ENGINE BEFORE STARTING.; Operation; STARTING; VACUUMING OPERATION; Use caution when using chipper; Your; TERMITE; chipper is designed to process tree branches; Under normal circumstances, allow time for machine; CHIPPING OPERATION; Maximum

Part No. 890424 Form No. F011398A Page 5 of 12 VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle andpulling height adjust rod (item 23) up at left rear of machine. FOR MAXIMUM PICKUP: A djust nozzle close to debris, but without blocking airflow into the nozz...

Page 6 - OPERATION; continued; Note: Frequently empty debris to prevent bag overloading with; DO NOT place bag on or near hot surface, such as engine.; Run; Run machine at idle to quar ter throttle.; DO NOT leave debris in bag while in storage.; DEBRIS BAG

Part No. 890424 Form No. F011398A Page 6 of 12 OPERATION continued 16 16 16 16 16 Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.An optional bag and dust cover is available for use where debris will bevacuumed in dusty conditions (see Optional Accessories...

Page 7 - Never store engine indoors or in enclosed poorly venti-; Do not store with debris in bag.; STORAGE; Tamper Storage Position; PROPULSION

Part No. 890424 Form No. F011398A Page 7 of 12 Before turning machine off, use the Tamper to slowly pushremaining pieces of wood through the chipper. This canprevent any remaining wood from jamming in the chipper whenmachine is turned off.Do not leave tamper on the ground, store tamper in the chippe...

Page 8 - MAINTENANCE; CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY; Chipper blades are normal replaceable wear items.; Chipper blade is sharp.; CAUTION: Be careful to avoid heat buildup; INCORRECT; IMPELLER REMOVAL and CHIPPER ADJUSTMENT; Wait for engine to cool and disconnect spark plug.; Using a penetrating oil can help loosen a; IMPELLER REMOVAL

Part No. 890424 Form No. F011398A Page 8 of 12 MAINTENANCE CHIPPER BLADE REMOVAL AND SHARPENING-TKD ONLY Depending on the type and amount of wood being chipped, thechipper blade will eventually get dull, losing it’s cutting ability.Evidence of a dull blade is a noticeably reduced chipping ability or...

Page 9 - Maintenance Operation; Maintenance Schedule; R o d; CLUTCH ADJUSTMENT; DRIVE

Part No. 890424 Form No. F011398A Page 9 of 12 MAINTENANCE continued IMPELLER REMOVAL continued 18. If chipper blade properly clears anvil surface, proceed to step . Ifnot, return to (step 14) and add or subtract shim washers asneeded to obtain a correct gap. 19. Reinstall engine and impeller onto h...

Page 10 - PARTS DRAWING

Part No. 890424 Form No. F011398A Page 10 of 12 R 18 18 18 18 18 PARTS DRAWING KD510SP, TKD510SP

Page 12 - Engine Service and Warranty; Contact your nearest engine manufacturer's autho-; Serial Plate; TROUBLESHOOTING; PARTS LIST

Part No. 890424 Form No. F011398A Page 12 of 12 Engine Service and Warranty Contact your nearest engine manufacturer's autho- rized servicing dealer. 22.1 22.1 22.1 22.1 22.1 22 22 22 22 22 BILLY GOAT INDUSTRIES INC.P.O. BOX 308 (1803 S JEFFERSON) LEE'S SUMMIT, MO 64063 / USAPHONE: 816-524-9666 FAX:...