BILLY GOAT HW650SP - Manuals

Page 2 - Part No. 510153; because contact may cause burns.; DO NOT transport unit with fuel in tank.; TABLE OF CONTENTS; VIBRATION; IN THE INTEREST OF SAFETY; The Engine Exhaust from this product contains chemicals known; SOUND

Part No. 510153 Form No. F102802D because contact may cause burns. 22. DO NOT run engine without air cleaner or air cleaner cover. 23. DO NOT operate during excessive vibra-tion!24. DO NOT leave machine unattended while in operation. 25. DO NOT park machine on a steep grade or slope. WARNING: DO 1. ...

Page 3 - GENERAL SAFETY; when operating mower.

Part No. 510153 Form No. F102802D Page 3 of 12 For your safety and the safety of others, these directions should be followed: Do not operate this machine without fi rst reading owner's manual and engine manufacturer's manual. Use of Eye and Breathing protection is recom- mended when using this machi...

Page 4 - INSTRUCTION LABELS; CONTROLS; Throttle Control; ASSEMBLY; WARNING; Manual; Manual; EVERY 10 HOURS; WARNING; WARNING; Speed Control; PATENT; DANGER

Part No. 510153 Form No. F102802D INSTRUCTION LABELS CONTROLS Throttle Control These labels should be included on your Contour mower. If any of these labels are damaged, replace them before putting this equipment into operation. Item and part numbers are given to help in ordering replacement labels....

Page 5 - in areas where bystanders may be present.; CUTTING OPERATION; OPERATION; STARTING

Part No. 510153 Form No. F102802D Like all mechanical tools, reasonable care must be used when operating machine. Do not operate unit in areas where bystanders may be present. D o n o t o p e ra t e i f ex c e s s i ve v i b ra t i o n o c c u r s. I f ex c e s s i ve v i b ra t i o n o c c u r s, s...

Page 6 - continued; FRONT CASTER LOCK

Part No. 510153 Form No. F102802D OPERATION continued 16 Front caster can be locked with a remote located on the rear of the machine for mowing on hillsides (fIg. 4 & 5).WARNING! Never mow on any slope greater than 15 degrees. ALWAYS mow across the face of slopes; never up and down or diagonally...

Page 7 - STORAGE; HILL; MAINTENANCE; Blade, and drive belts are normal wear items.; ENGINE; Maintenance Schedule; MAINTENANCE HISTORY; Service Performed

Part No. 510153 Form No. F102802D Never store engine indoors or in enclosed poorly ve n t i l a t e d a r e a s w i t h f u e l i n t a n k , w h e r e f u e l f u m e s m ay r e a c h a n o p e n f l a m e, s p a r k o r p i l o t l i g h t , a s o n a furnace, water heater, clothes dr yer or other...

Page 8 - BELT REPLACEMENT; BLADE REMOVAL / SHARPENING; Blade Drive Belt

Part No. 510153 Form No. F102802D NOTE: When sharpening the blade it is a good idea to check the balance of the blade. A properly balanced blade will increase life of the bearings and other components. Tools required: 3/8 inch socket, 5/8 inch socket, torque wrench, blade block.1. Disconnect spark p...

Page 9 - Drive Belt; SELF PROPELLED DRIVE ADJUSTMENT

Part No. 510153 Form No. F102802D Page 9 of 12 Drive Belt Tools required: 3/8 inch socket, 1/2 inch socket, 3/8" torque wrench. 1. Follow steps 1 through 5 above to remove the blade drive belt.2. Set the unit on its side to allow access to both pulley and the blade.Note: When tipping the unit on...

Page 10 - PARTS DRAWING

Part No. 510153 Form No. F102802D 9 89 23 22 23 24 25 6 49 103 102 includes 68 99 33 36 40 38 90 85 43 44 71 96 78 96 71 96 93 112 5 96 71 5 70 53 45 46 104 94 72 34 77 92 27 26 29 32 31 30 71 71 97 28 86 88 37 50 63 51 52 42 40 69 85 39 43 68 20 21 72 82 19 76 76 11 13 98 14 16 15 95 70 17 65 107 1...

Page 12 - Engine Service and Warranty; Contact your nearest engine manufacturer's authorized; Serial Plate; Solution; TROUBLESHOOTING

Part No. 510153 Form No. F102802D Page 12 of 12 Purchased from Purchase Date Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 22.1 21 Serial Plate R ecord your machine model, serial number and date-of-purchase and where purchased 22 R BILLY GOAT IND...