Best UP271 - Manuals - manualsarea.com

Page 3 - INTERIOR BLOWER

HL0086 - 3 - Model 415 (7” round adjustable elbow, optional) Model 418 8” round adjustable elbow, (optional) UP27I SERIES HOOD (Canopy with internal blower, controls & lighting. Required for all installations.) NON-DUCT KIT FLUE ANKUP SERIES - UP27I SERIES RANGE HOOD SYSTEM - INTERIOR BLOWER Mod...

Page 4 - IN-LINE AND EXTERIOR BLOWERS

- 4 - HL0087 - UP27E SERIES RANGE HOOD SYSTEM - IN-LINE AND EXTERIOR BLOWERS In-line and exterior blower rough-in kit(included with EB6, EB9, EB12, EB15,ILB3, ILB6, ILB9 and ILB11 blowers.) Model 418 10” Round adjustable elbow (optional) Model ILB3 (280 cfm) in-line blower (includes one 8” to 10” ro...

Page 5 - SELECT BLOWER OPTION AND INSTALLATION TYPE; TYPICAL RECTANGULAR DUCTWORK

- 5 - 1. SELECT BLOWER OPTION AND INSTALLATION TYPE 1.2 D UCTED I NSTALLATION Either UP27I or UP27E Series range hoods may be ducted. For a UP27E Series range hood, either an exterior blower or in-line blower may be used. The Best by Broan UP27E Series must be installed with blower models ILB3, ILB6...

Page 6 - PREPARE THE INSTALLATION; CAUTION; REMOVE THE FILTERS

Remove the installation kit from inside the hood. Make sure that the following items are included: - Installation manual - Adapter/damper 3¼” x 14” to 3¼” x 10” (exclusively for UP27I Series range hoods, temporarily assembled to pan, behind Evolutionary™ hybrid baffle filters) - Adapter/damper 3¼” x...

Page 7 - PREPARE THE CABINET; REMOVE THE GREASE DRIP RAIL

- 7 - 7. PREPARE THE CABINET For cabinets with recessed bottom, attach two wood filler strips cut to length (not included), on each side, as shown below. Seetable below for wood filler strips location. HD0208 L C A A H OOD C ENTER OF WOOD WIDTHS STRIP LOCATION ( A ) 30” 13 3 ⁄ 8 ” 36” 16 3 ⁄ 8 ” 42”...

Page 8 - ANKUP S

- 8 - 7. PREPARE THE CABINET (CONT’D) 7.1 D UCTED I NSTALLATION : Cut-out the openings for duct ( A ) and house wiring (120 V AC)( B ) according to the directionof discharge chosen. See figures beside. NOTE: For all UP27I Series (inter nal blower) range hoods, the cut-out opening for house wiring (1...

Page 10 - WARNING

- 10 - 8. PREPARE THE HOOD (CONT’D) 8.1 UP27I S ERIES RANGE HOOD ( INTERNAL BLOWER ) ( CONT ’ D ) H ORIZONTAL D ISCHARGE (D UCTED INSTALLATION ONLY )( CONT ’ D ) Using 3 no. 8 x 3/8” screws provided with hood, secure the adapter/damper on the back of the hood. Remove tape from damper flap. Seal the ...

Page 11 - INSTALL THE BLOWER; Do not plug the two cords into each other.; A A

- 11 - 10.INSTALL THE HOOD Place the hood at its location. Using a pen, mark the position of the screw (smaller part of the keyholes [ A ]). Remove the hood and install (4) 1/2” double thread screws at marked positions, leaving a 1/8” gap.Place the hood under the cabinet and slide it in position. Ma...

Page 12 - REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS; LIGHT BULBS REPLACEMENT

Reinstall the grease drip rail. 13.REINSTALL GREASE DRIP RAIL AND BAFFLE FILTERS 13.1 D UCTED I NSTALLATION : Reinstall Evolutionary™ hybrid baffle filters on the hood. 13.2 N ON -D UCTED I NSTALLATION : Slide out and discard the secondary micromesh filters from the back of the baffle filters. Slide...

Page 14 - HEAT SENTRY; WARRANTY

- 14 - 16.OPERATION (CONT’D) HEAT SENTRY Both UP27I and UP27E series are equipped with a HEAT SENTRY thermostat. • If blower is ON at a lower speed setting and excessive heat is detected above the cooking surface, it turns the blower up to HIGH speed. When the temperature level drops to normal, the ...

Page 15 - SERVICE PARTS

- 15 - SERVICE PARTS KEY PART QTY (HOOD WIDTH) NO. NUMBER DESCRIPTION 30’’ 36’’ 42’’ 48 1 V14971 A DAPTER / DAMPER 3¼” X 14” 1 1 1 1 2 T461 A DAPTER / DAMPER 3¼” X 14” TO 3¼” X 10” 1 1 1 1 3 V03435 T HERMISTOR H EAT S ENTRY 1 1 1 1 4 V07834 R OTARY C ONTROL 2 2 2 2 5 V07689 T OGGLE S WITCH 2 2 2 2 6...