BenQ HDR-16EP - Manuals

7 IV. OPERATION The operation procedures are as follows: 4-1 Booting Up 1. Push the Power Button (Open the front panel, then press the button). 2. If all the installation procedures are correct, the system will boot up and show the main screen as follows. HDR-16EP

8 4-2 Main Screen The above picture is an example of the main screen. On the right of the screen is the “status display”. From top to bottom is Date/Time, Hard Disk Free Space, then followed by 3 columns and 16 rows, which are Recording Status (1 st column), DI Receiving Status (2 nd column), and DO...

9 4-3 Display Mode The 7 icons on the bottom of the Main Screen are Display Mode selections. The 7 icons are 4 splits, 6 splits, 8 splits, 9 splits, 10 splits, 13 splits, and 16 splits. The default display mode is 16 splits. The camera displayed on each split mode could be modified through the syste...

14 4-6 System Settings 4-6-1 、 Enter System Settings Screen 1. Click the System Setting icon. System will show a screen as follows for user to key in the username and password. 2. Use mouse to click the “keyboard” icon on the right of the “User Name” column. System will show up a “keyboard figure” a...

16 4-6-2 Camera Setup 1. Please select the camera you would like to do the setting. 2. Camera Name: You could use the “keyboard figure” icon on the right of “Camera Name” column to key in the description for the camera. 3. Enable/Disable: If the channel is not connected to camera, please set “Disabl...

19 4-6-3 View Setup Click “Split” icon, it will display the view setup screen as follows. For the 7 display modes mentioned in the section 4-3, the display content is setup through the “Split” icon on the screen above. For the table above, there are 4 splits, 6 splits, 8 splits, 9 splits, 10 splits,...

20 4-6-4 User Account Management This section describes the “remote access privilege” setup procedures for the user account. Click “User” icon, it will display the screen for user account management as follows. [Add User Account] Click “Add” icon to add user account as screen below.

21 1. There are 2 system pre-set accounts. The usernames and passwords for these two accounts are as follows. 1-1 Username: “admin”; Password: “1111” is for system management account. This account could not be deleted. 1-2 Username: “net”; Password: “1111” is for normal user account. This account co...

25 (3) One IO-1616 module, which includes 1 board (for internal connection), 4 cables (for internal connection), 1 board (for external connection), and 1 cable (for external connection).. 2 DI control options: 2.1 Disable: Disable the “control signal input”. 2.2 NC (normal close): signal loop is nor...

26 4. No matter it’s DI status change or image motion, it all counts as Event happening, so it will start the recording, If the DO is enabled, the DO status will also be changed if the event happens. Please refer to the graph below. 4-6-8 、 Exit the System Setting Screen After finishing all the nece...

28 4-7-1 、 Remote Monitoring through Local Area Network [Administrator] Decide an IP address in the local area network. Follow the instruction in 4-6-6 “Network Configuration” to set up HDR-16EP, then connect HDR-16EP to the local area network. Inform user the IP address, username, and password. [Us...

29 4-7-2 、 Remote Monitoring through the Internet via Modem [Administrator] To allow users to do the remote monitoring through Internet, Administrator of HDR-16EP needs to apply for a fixed line (leased line or ADSL), and get the fixed IP address from the ISP (Internet Service Provider). Please foll...

31 4-7-3 、 Remote Monitoring when HDR-16EP Connects to Modem Similar to dialing up to ISP (Internet Service Provider) for connecting to internet as the previous section, through modem to connect to HDR-16EP(direct dial-in) is another way to do the remote monitoring. The only difference is that direc...

32 Enter the phone number of the modem connected to HDR-16EP. Click on “Next” to complete the setup. After completing all the setup procedure, open “Dial-Up Networking” window, you will see the “HDR-16EP” Icon 。 Double click the “HDR-16EP” Icon, then enter the dial-up username and password as left g...

35 4-7.5 How to use Remote Monitoring and Remote Playback After the installation, you can start using Remote Monitoring and Remote Playback functions by clicking on the icons on the HDR-16EP web page. The following screen will be displayed: [Remote Monitoring Function]: There are three kinds of disp...

36 “4 Split”: User could monitor 4 split screen at the same time as the graph below. The default view is Camera 1,2,3,4, Camera 5,6,7,8, Camera 9,10,11,12, and Camera 13,14,15,16. User could also change the view position of each camera from the “Custom View” column. “16 Split”: It will display all t...

40 for retrieving purpose in the future. Insert the new removable hard disk (purchased from the dealers authorized by Hung Electronic USA, Inc.) and lock the hard drive with key. Turn on the power switch. The system will recognize the new disk and request to format it. Click “Yes” to accept disk for...

41 2. Click “ Format” on the right of the screen, then system will start to format the new hard disk. After finishing the format, the “selection icons” will become “available”. Please refer to the figure below. Use the “selection icons” to choose the cameras you would like to be recorded in this new...

42 4-8-2 、 If the old disk is inserted to the system. After system booting, it will show as follows. 1. If you click “Play Only” icon , it will show the figure as follows. Selection Icons Selection Icons

44 stored in these two HD, the “All Disk” icon will pop up also. User could click the “All Disk” icon, then click the “Playback” icon to enter playback screen to play the images stored in these two HD. 2. If you click “Disk Management” icon , it will show the figure as follows. If there are two old ...

45 Please use the “Selection” Icon as above to remove the “overlapped camera” from one of the HD, then the “Save” icon will pop up again. Click the “Save” icon, the system will reboot automatically and start the normal operations and record the data in these two HD Remark : * If the HD is entering t...

47 2. Blank CD-RW: If the CD-RW is used, please execute “Blank” procedure first. Input the CD-RW to the CD-R/RW recorder, click on to start the clean up process. After it is done, the Message area will display “Done”. If the CD-RW is the blank one, you do not need to execute this process. 3. Select ...

49 V. OTHER INFORMATION 5-1 Specifications Model ： HDR-16EP System: Operation System Embedded Linux Video Input 8/16 BNC connectors Video Output D-type VGA connector Video Format NTSC/PAL/SECAM Compression MPEG-4 User Interface User friendly graphic user interface operated by mouse Security Multiple...

51 5-3 Maintenance 1. Avoid placing the system in a high temperature or a high humidity environment and also away from the place with frequent vibrations. 2. Operate the system under stable voltage. If possible, operate the system with a UPS (Uninterruptible Power Supply). 5-4 Warranty Hunt Electron...