Axor 04126XX0 - Manuals - manualsarea.com

Page 3 - Three-hole thermostatic tub filler -- requires rough 04124181

3 Three-hole thermostatic tub filler -- requires rough 04124181 04129XX0 04128XX0 04127XX0 04126XX0

Page 4 - Technical Information; Recommended water pressure; Installation Considerations; temperature limit stop may be reset to comply with these codes.

4 Technical Information Recommended water pressure 45 - 72 psi Recommended hot water temp. 120 � - 140 � F* Max. hot water temp 165 � F* Max. flow rate 8 gpm Max. flow rate – handshower 2.5 gpm Safety stop 100° F *Please know and follow all applicable local plumbing codes when setting the temperatur...

Page 5 - Install the valve trim; mm Allen wrench. The screw must; Over tightening the screw may; Install the spout; slot

5 Install the valve trim Push the escutcheon over the valve.Install the handle. Tighten the screw with a 3 mm Allen wrench. The screw must engage the slot on the cartridge.Justify the handle.Set the high temperature limit stop. Push the spout sealing ring firmly into the spout adapter (1).Push the e...

Page 6 - Install the handshower; Pull the end of the handshower hose from the

6 Install the handshower Pull the end of the handshower hose from the holder. Push the escutcheon over the end of the hose. Push the elbow firmly over one end of the handshower hose. Tighten the hose nut. Thread the hose down through the handshower holder escutcheon and handshower holder. Tighten th...

Page 7 - Set the high temperature limit stop

7 Set the high temperature limit stop Turn the water on to the tub spout or handshower. Use a 3 mm Allen wrench to loosen the handle screw. Remove the handle from the valve. Carefully remove the retainer clip and the limit stop ring. Turn the temperature control stem until the water is the desired h...

Page 8 - Justify the handle

8 Justify the handle Turn the water on to the tub spout or handshower. Place a thermometer in the water stream. Turn the temperature control knob until the output wa- ter temperature is 100°F. Turn the water off. Install the stop ring so that it is against the stop -- you should not be able to turn ...

Page 11 - Maintenance: Clean the filters; Turn off the water at the main

11 Maintenance: Clean the filters Turn off the water at the main before opening the valve. Remove the handle and escutcheon. Rinse the handshower with clear water. Install the handshower. Turn on the water and flush the hand- shower for at least one minute. If scale deposits build up on the spray fa...

Page 12 - Failure to hold the stop unit; Grasp the wrench flats on the cartridge stop unit; Failure to hold the stop unit steady

12 Install the escutcheon.Justify the handle. Rinse the debris from the filters, using a soft toothbrush if necessary. Do not at- tempt to remove the screens.Lubricate the o-rings with white plumbers grease. Hold the stop unit steady. Install the ther- mostatic cartridge. Failure to hold the stop un...

Page 13 - Replacement parts

13 Replacement parts 1 2 6 4 5 3 7 8 12 13 14 15 16 17 18 8 8 8 8 8 8 12 12 12 12 14 14 14 15 15 15 15 13 13 16

Page 14 - Troubleshooting; Problem

14 1 Solaris E handle 88530XX0 2 Talis S handle 88549XX0 3 C handle 88610XX0 4 Metris S handle 88713XX0 5 Focus S handle 88714XX0 6 Allegro E handle 88719XX0 7 Metro E handle 88721XX0 8 handle escutcheon 88734XX0 9 elbow 28071XX0 10 handshower escutcheon 97159XX0 11 check valve 94074000 12 spout sea...