Atlantic ODYSSEO2 - Manuals

- 3 - Presentation of the product How it works The heat pump water heater uses unheated air to prepare domestic hot water. Heat energy extracted from the ambient air is absorbed by the refrigerant through heat transfer at the Evaporator. This energy is concentrated by the Compressor and then transfe...

- 4 - Technical characteristics Dimensions mm H 1897 x l 591 x D 674 Empty weight kg 90 Capacity of the tank L 270 Hot water / cold water connection 3/4 ’ ’ M Corrosion-proof protection Impressed current anode Minimum conductivity of the water μ S/cm 40 Rated pressure Permissive excessive operating ...

- 5 - Dimensions / components 1 Air outlet 10 Hot water inlet 2 Air inlet 11 Compressor 3 Fixed unit attachment 12 Evacuation of condensate 4 Fixed feet 13 Compressor permanent condenser 5 Cold water inlet 14 Evaporator 6 Pocket 15 Fan wiring 7 Sheath 16 Fan 8 Electric heating element (ceramic eleme...

- 6 - Installation Selecting the location in compliance with IEC 60 529 Standard, AS60529:2004 Resistance of the floor  Capable of withstanding a weight of at least 400 kg (the area under the water heater) The place where the appliance is installed must comply with protection index IP X1B according...

- 7 - Recommended configurations 1 st Configuration : installation without ducts in an unheated space (Volume > 20m 3 ) FAN set to 0 (see Setting the regulation section, page 15). Examples of unheated rooms: - Garage: recovery of free heat released by the car engine after use or by other househol...

- 8 - Configuration tolerated under certain conditions Installation in an unheated space with one duct (outlet or inlet, volume > 20m 3 ) FAN set to 1 (see Getting start section, page 14). Possible consequences: - The negative pressure in the room due to the expulsion of the exterior air may resu...

- 9 - Installing the product 1- Transport the water heater to the place where it is to be installed. 2- Cut the cardboard skirting along the dotted lines. 3- Take the water heater off the pallet and place it by the hydraulic connection. MAXIMUM! The water heater must be installed on a smooth and hor...

- 11 - Air connections . Your heat pump water heater can be fitted with ducting accessories that are not supplied with the water heater. If the volume of the room in which the thermodynamic water heater is installed is insufficient, it can be connected to 160 diameter air ducts. If the air ducts are...

- 12 - Electric connections Caution: the water heater must be filled with water first, before making the electric connections (see Getting started section, page 14 ). The HPWH must remain connected to the main power supply at all times so that the operation of the (ACI) anti-corrosion protection of ...

- 13 - Electric connections FOR RIPPLE CONTROL: NEW ZEALAND ONLY 240 volt supply with 2 amp protection connected to the black auxiliary wire. Set HCHP parameter to ON, see page 15 setting the regulation. The diagram shown is only the functional configuration. Wiring details (ie. switching, fusing, m...

- 14 - Getting started 1. Filling the water heater.  Fill the water heater by opening all hot water taps and opening the cold water inlet to allow the water heater to fill and air in the system to be expelled. Close each hot water tap, as the flow becomes free of air. Check all piping for leaks.  ...

- 15 - 3. Setting the regulation Adjusting the temperature set point The temperature setting of your appliance is adjusted to 55°C in the factory. It can be adjusted simply by pressing & directly on the default display. The lower the temperature setting of the heat pump, the better the coefficie...

- 16 - Use Control panel Description of the pictograms: Symbol Name Description Compressor Status of the compressor: Compressor working Flashes slowly Fan Status of the fan: Low speed → Flashes slowly High speed → Flashes quickly Sensor Indication of the physical position of the sensors Sensor assoc...

- 17 - Incoming air temperature Air temperature sensor in the flow of ambient air Evaporator temperature Temperature sensor on a cross in the evaporator Water temperature Water temperature sensor in the pocket Heat pump time Shows the working time of the water heater heat pump in hours Elec time Sho...

- 18 - ECO mode This mode uses the heat pump only to produce hot water. Under certain conditions, this mode may result in shortages of hot water (mainly due to air temperatures outside the operating range). BOOST mode BOOST mode can be used to force the heat pump and the electric backup to work at t...

- 19 - Adapting the mode of your appliance to your needs 1. Calculate your daily needs in terms of a number of showers (1 bath = 3 showers) Example: daily need = 3 showers + 1 bath => 6 showers 2. Identify the mode that best meets your needs in the table below Number of showers per day AUTO ECO *...

- 20 - Recommendations – Maintenance & Repairs Advice for users  Flushing of sediment and draining : To flush or to drain the water heater, power must be turned off and then turn off the cold water supply to the water heater. The lever on the pressure and temperature relief valve should be open...

- 21 - Maintenance by a qualified professional To protect the performance of your appliance for many years to come, it must be checked by a professional every 2 years.  Switch off the electric power supply (circuit breaker, fuses, etc.).  Drain the tank:  close the cold water inlet (isolating val...

- 22 - Troubleshooting . Alarm codes on the control panel: The buzzer can be stopped or reset by pressing one of the following keys: , or Code Condition under which the error occurs Cause Consequences Repair Err 03 Water temperature sensor in the pocket faulty  Sensor cut out or shorted  No heatin...

- 23 - Fault diagnosis for professionals IMPORTANT Maintenance and repair operations must only be performed by qualified professionals. A specific menu is available to operate the system and help you with your diagnostic. This mode requires technical knowledge of the system. This mode is strictly fo...

- 24 - Heating element or its wiring partly out of order Check the resistance of the plug on the connector on the plug wiring and the condition of the wiring. Cold water returns into the hot water circuit. Close the cold water supply using the isolating valve. Then open a tap in the hot water positi...

WARRANTY CERTIFICATE TO BE KEPT BY THE USER OF THE APPLIANCE ODYSSEO 2 HEAT PUMP WATER HEATER USING NON-HEATED AIR Duration of the warranty* - Water heater (cylinder): 5 years in domestic installations 3 years in commercial installation - Electric elements and components parts: 2 years in domestic i...