Aquatic LuxeAir Series - Manuals

aquatic Industries, Inc. 5 imPOrTANT SAFETy iNSTruCTiONS wArNiNg: wheN usINg ThIs uNIT, These BAsIc PrecAuTIONs shOuLD Be FOLLOweD. This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal ...

aquatic Industries, Inc. 6 wArNiNg: All units are shipped with loose unions. Before attempting to test, install or use your whirlpool, all pump and heater unions and “O” rings must be repositioned and/or tightened. PLEASE NOTE: ThE mANuFACTurEr ACCEPTS A 1/4” VAriANCE. ThErE ArE VAriATiONS ON EACh T...

aquatic Industries, Inc. 7 Note: The bath should remain in its shipping carton until time of installation. 1. Literature dimensions are for reference only. Installation dimensions should be taken directly from the tub. An access panel of 30”w x 20”h minimum must be provided at the pump end of the wh...

aquatic Industries, Inc. 8 SEE iLLuSTrATiON 2A A. Install the whirlpool bath unit per the instructions provided in this manual. CAuTiON: ThE TiLE FLANgE dOES NOT SuPPOrT ThE TuB! A ledger board must be provided under the bath rim as indicated in the installation instructions. Take care to ensure tub...

aquatic Industries, Inc. 9 1. To avoid obstructions during installation, make sure water lines, spout pipes and valve plumbing do not project into alcove. 2. Ledger Strip: Fasten a 1” x 3” (25mm x 75 mm) ledger strip along rear for alcove and along both sides in corner installations at Dimension Lh....

aquatic Industries, Inc. 10 rOugh-iN mEASurEmENTS: iNSTALLATiON iNSTruCTiONS mOdEL A B (From center of overflow pipe (From center of to outside rim) drain to tub rim) LuxeAir 21 6 1/2” 13 1/4” LuxeAir 22 2 1/4” 12” LuxeAir 23 5 3/8” 12” LuxeAir 24 6 3/4” 14” LuxeAir 25 5 1/4” 16 1/4” LuxeAir 26 6 1/...

aquatic Industries, Inc. 11 iNSTALLATiON iNSTruCTiONS wArNiNg: ALL eLecTrIcAL cONNecTIONs shOuLD Be MADe BY A LIceNseD, LOcALLY cerTIFIeD eLecTrIcIAN, IN AccOrDANce wITh The reQuIreMeNTs OF The NATIONAL eLecTrIcAL cODes AND PrOceDures. wArNiNg: wheN usINg eLecTrIcAL PrODucTs, PrecAuTIONs shOuLD ALwA...

aquatic Industries, Inc. 12 BONdiNg wirE: Connect a #8 bare copper bonding wire from the pump motor to the heater and then to the cold water plumbing or other suitable ground. grounding is required. grounding is NOT required for the blower. breaker panel 15 AMP2 POLEGFCIBREAKER 15 AMP1 POLEGFCI BREA...

aquatic Industries, Inc. 13 LuxEAir BLOCK diAgrAm Dedicated 15 amp 110vac w/GFCI 1 Pole Breaker 20 Minute Timer Control for blower Part # 1102 key pad Part# 1104PAD Dedicated 15 amp 110vac w/GFCI 2 Pole Breaker 20 Minute Timer Control for pump Part # 1103 pump Motor Part # 8108MOTOR blower Motor Par...

aquatic Industries, Inc. 15 OPErATiON of LuxEAir SEriES NOTE: dO NOT STArT PumP uNTiL ALL jETS ArE SuBmErgEd. wATEr LEVEL ShOuLd BE 2” ABOVE highEST jET. jET OPErATiONS: FuLL SizE PrESSurE-FLO hydrOThErAPy jET: All Full-size Pressure-Flo hydrotherapy Jets can be interchanged with the hand held Jet. ...

aquatic Industries, Inc. 17 Operation of the inline maintenance heater is completely automatic. The heater will help maintain the temperature of the water in the whirlpool. The heater includes the following components. TherMOsTAT: The “smart Thermostat” requires no adjustment and will automatically ...

aquatic Industries, Inc. 18 LuxEAir SEriES CONTrOL PANEL To Turn Blower (Air System) On: Press once to turn the blower (air system) on. A second press will turn the blower off. Holding the button down for 2 seconds will change modes when the blower is on. There is a 20 minute timer that will automat...

aquatic Industries, Inc. 19 ELECTrONiC CONTrOL PANEL (see Diagram 11A) : 1. To Turn Air Bath System On: Pressing the on/off button will turn the blower on in “constant mode.” The light indicator will illuminate when the system is on. The blower and the heater will automatically shut off after a 20-m...

aquatic Industries, Inc. 20 PurgE 24 hOurS: It is possible for the user to program a purge cycle that will start every day for a duration of 1 minute. Aquatic strongly recommends activating this feature. The purge cycle will help ensure that the air channels stay dry even when you have taken a soaki...

aquatic Industries, Inc. 21 OPErATiON of LuxEAir with OPTiONAL ChrOmAThErAPy OPTiONAL ChrOmAThErAPy LEd LighTiNg: To Turn your Chromatherapy Lighting System ON: Press the light button once to turn the Chromatherapy Light on in color wash mode. A second press of the button will turn the lighting syst...

aquatic Industries, Inc. 22 mAiNTENANCE ANd CArE iNiTiAL CLEANiNg: Before tub is used, the whirlpool system should be cleaned and disinfected. remove all debris and clean tub before putting whirlpool into service. DO NOT use ABrAsIve cLeANers ON The AcrYLIc FINIsh. use a non-abrasive detergent and r...

aquatic Industries, Inc. 25 The whirlpool action may cause even small amounts of bubble bath or shampoo to foam excessively. Exercise moderation in experimenting with different soap products. No servicing of this product should be done by the user. There are no user serviceable parts. All controls a...

aquatic Industries, Inc. 26 mAiNTENANCE ANd CArE Owners of fill and drain whirlpool bathtubs need to know basic information concerning water quality: how it affects performance and enjoyment of the operation of their tubs, and steps that can be taken by the owner to correct related problems. Importa...

aquatic Industries, Inc. 27 TrOuBLEShOOTiNg guidE wArNiNg: Always turn off power at the main electrical service panel when servicing your whirlpool. Motor does not start 1) gFCI or circuit breaker in OFF position. 1) Reset gFCI. 2) Fuses blown or thermal overload open. 2) Contact your electrician. 3...

aquatic Industries, Inc. 28 rEPLACEmENT PArTS OrdEr FOrm FOr LuxEAir SEriES how To use: 1. Find your part on the map and make note of its number & letter. 2. using map number and letter, choose part number and select color (or finish) on parts list provided on page 32-33. 3. Fill out the form be...

aquatic Industries, Inc. 30 Fx101 Fx102 Fx103 Fx104 Fx105 Fx106 Fx107 LuxEAir SEriES rePLAceMeNT PArTs OrDer MAP/OvervIew ASSOrTEd FiTTiNgS Coupler y Fitting Street 90 o 90 o fitting T fitting Street 45 o 45 o fitting 1’’ or 1 1/2” 1’’ only 1/2”, 1” or 1 1/2” 1/2”, 1” or 1 1/2” 1” or 1 1/2” 1” or 1 ...

aquatic Industries, Inc. 32 LuxeAir Bath Parts List iLLuSTrATiON NO. dESCriPTiON - SPECiFy COLOr/FiNiSh/mOdEL# PArT NO. 1a. Pressure FLO JeT-BIscuIT 87DIrecTBI 1a. Pressure FLO JeT-BLAcK 87DIrecTBK 1a. Pressure FLO JeT-BrusheD NIcKeL 87DIrecTBN 1a. Pressure FLO JeT-BONe 87DIrecTBO 1a. Pressure FLO J...

Aquatic industries, inc. Limited Lifetime warranty For millennium, infinity, Century, LuxeAir and Luxury Series whirlpools, Serenity Air Baths, Serenity Studio, hotSoak Series Baths and restoration Series Limited warranty For Original Consumer For household usage whAT PrOduCTS ArE COVErEd structures...