Page 3 - table oF contents
Product registration inForMation 4 congratulations! 5 saFety instructions 6 installation instructions Pre-Installation Procedures 7 Electrical Installation 8 Structural Preparation 9 Framing Diagrams 10 Integrally Skirted Whirlpools 11 Flat Panel Skirt Installation 12-14 System Test and Clean-Up 15 ...
Page 4 - Product registration information
aquatic Industries, Inc. Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims....
Page 5 - or warranty will be voided. see page 7 for instructions.
aquatic Industries, Inc. note: The installation and service of your whirlpool should be performed ONLY by a qualified electrician, technician or plumber. You have chosen one of the finest bath products in the world! Aquatic Industries supports your purchase with strong commitments to quality and cus...
Page 6 - iMPortant saFety instructions; read and FolloW all instructions; saVe these instructions
aquatic Industries, Inc. iMPortant saFety instructions Warning: When using this unit, these basic Precautions should be FolloWed. This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal in...
Page 7 - read all instructions careFully beFore installation
aquatic Industries, Inc. 1. This whirlpool is factory-assembled, complete with motor, pump, controls and plumbing. do not lift or support unit using plumbing lines or any part of circulation system. do not relocate or otherwise modify any part of the factory-installed circulation system, as this may...
Page 8 - installation instructions; electrical installation:
aquatic Industries, Inc. When using electrical products, basic precautions should always be observed, including the following:1. read and FolloW all instructions. 2. circuit: A separate circuit (not to supply any other electrical devices) is required as follows: For units equipped with a pump motor ...
Page 9 - tyPes oF installations:; structural PreParation:
aquatic Industries, Inc. Framing and supports will vary according to the model and type of installation selected. 1. Plumbing connections: (spout, handles, valves, etc.) should be made after unit is installed. When mounting fittings on unit, drill holes from finished surface, using appropriate-sized...
Page 10 - alcoVes
aquatic Industries, Inc. 10 installation instructions rectangular Models ↔ corner Models ↔ oval Models ↔ decK cutout: A paper template will be enclosed with all oval models. For the deck cutout, scribe on the deck two center lines (a major and minor axis). Next, match the center lines and trace the ...
Page 11 - reMoVable sKirt Panel For integrally sKirted Models:; installation instructions; integrally sKirted WhirlPools:
aquatic Industries, Inc. 11 reMoVable sKirt Panel For integrally sKirted Models: These models are offered with removable access panels. They provide a flush-to-wall installation (sheet rock overlaps skirt while still providing access). The skirt features a decorative removable panel enabling easy ac...
Page 12 - Flat Panel sKirt installation instructions
aquatic Industries, Inc. 12 Parts included For installation: 4 - Spring clips8 - #6, ½” self tap screws for spring clips3 - #8, 1¾” stainless steel screws (use 2 for 5’ skirts, 3 for 6’ skirts)3 - Chrome decorative caps3 - Brass decorative caps3 - Decorative cap holders9 - Decorative caps in assorte...
Page 16 - syMPhony WhirlPool jets; oPeration oF syMPhony
aquatic Industries, Inc. 1 jet oPerations: The Symphony Series uses spinning back jets and directional jets to provide an invigorating hydrotherapy experience. aquatic directional jet: • to adjust pressure (see diagraM 10a): 1. grasp the outer ring of the jet. 2. Turn the outer ring counter clockwis...
Page 17 - beFore your First use:; to oPerate your WhirlPool:; WhirlPool oPerations:
aquatic Industries, Inc. 1 oPeration oF syMPhony WhirlPools Your whirlpool bathtub features a built-in circulating system that mixes the bath water with air and pumps the mixture back into the bathtub creating the hydromassage action. Because it is a bathtub, it must be drained after each use. The c...
Page 19 - Maintenance and care; WhirlPool systeM cleaning:
aquatic Industries, Inc. 1 Maintenance and care Before tub is used, the whirlpool system should be cleaned and disinfected. Remove all debris and clean tub before putting whirlpool into service. DO NOT USE ABRASIvE CLEANERS ON THE ACRYLIC FINISH. Use a non-abrasive detergent and rinse well after cle...
Page 20 - Microbiological quality; surFace scratch reMoVal:; Water quality issues:
aquatic Industries, Inc. 20 Maintenance and care Owners of fill and drain whirlpool bathtubs need to know basic information concerning water quality: how it affects performance and enjoyment of the operation of their tubs, and steps that can be taken by the owner to correct related problems. Importa...
Page 22 - WhirlPool user inForMation; Electrical installation information listed on page 8.
aquatic Industries, Inc. 22 The air bath action may cause even small amounts of bubble bath or shampoo to foam excessively. Exercise moderation in experimenting with different soap products. No servicing of this product should be done by the user. There are no user serviceable parts. All controls ar...
Page 23 - troubleshooting guide; syMPtoMs; serial number location
aquatic Industries, Inc. 23 troubleshooting guide Warning: Always turn off power at the main electrical service panel when servicing your whirlpool. Motor does not start 1) gFCI or circuit breaker in OFF position. 1) Reset gFCI 2) Fuses blown or thermal overload open. 2) Contact your electrician. 3)...
Page 24 - Please fill ouT comPleTely:; rePlaceMent Parts order ForM; For syMPhony series
shiP to: Name Company Address City State zip Phone Fax how to use: 1. Find your part on the map and make note of its number & letter.2. Using map number and letter, choose part number and select color (or finish) on Parts List provided on page 25.3. Fill out the form below with the selected info...
Page 25 - Jet
aquatic Industries, Inc. 2 syMPhony rePlaceMent Parts order MaP 2a. On/Off Air Button2b. Air Button Assembly 1a. Suction Cover 3a. Directional Jet 3c & d. Jet Body with Wall Fitting 4a. .80 HP Pump 6a. Pump Base 5a. Safety Suction valve 1c. 1b. 1b. Suction Wall Fitting1c. Suction Elbow Part 7b. ...
Page 26 - descriPtion
aquatic Industries, Inc. 2 syMPhony rePlaceMent Parts list * to indicate color, replace “XX” with “Wh” for White, “bo” for bone, “bK” for black, “st” for sterling silver, “bi” for biscuit, “cl” for clear and “br” for oil rubbed bronze. descriPtion Part # color/Finish 1a. Suction Cover 8152HvSUCvRXX*...
Page 27 - aquatic industries, inc. limited Warranty
aquatic industries, inc. limited Warranty For symphony series Whirlpools limited Warranty For original consumer For household usage What Products are coVered Structures and surface finishes on Whirlpools (“Whirlpools”) and Soaking Tubs (“Tubs”), and their support equipment, components, attachments, ...
