Page 2 - AMX Limited Warranty and Disclaimer
AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted fo...
Page 3 - Software License and Warranty Agreement; INTELLECTUAL PROPERTY.
Software License and Warranty Agreement LICENSE GRANT. AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, not sold. This license does not grant Licensee the right to create derivative works of the AMX Software...
Page 5 - Table of Contents
Table of Contents i Enter the Document Name Here Table of Contents NXF CardFrame and NetModules ...................................................................... 1 NXF CardFrame ........................................................................................................ 1 NXF Cardfr...
Page 7 - NXF CardFrame and NetModules; NetLinx Control Cards can be installed in the NetLinx; NXF CardFrame; front
NXF CardFrame and NetModules 1 NetLinx Cardframe, Control Cards, and NetModules NXF CardFrame and NetModules NetLinx Control Cards can be installed in the NetLinx ® (NXF) CardFrame, the NI-4000, or in modules for stand-alone operation. The NXF CardFrame accommodates a NetLinx Master (or Hub) card, u...
Page 8 - NXF Cardframe Specifications; Mounting Master/Hub Cards in an NXF CardFrame; Unplug all the connectors from the NXF.; Front Panel Components:; Rear Panel Components:
NXF CardFrame and NetModules 2 NetLinx Cardframe, Control Cards, and NetModules NXF Cardframe Specifications Mounting Master/Hub Cards in an NXF CardFrame NetLinx Master and Hub Cards can be installed in the NXF CardFrame. The card mounts in a horizontal position, through the master card slot on the...
Page 9 - Setting the CardFrame's starting address; A card in slot number 7 would be device address 2023.; Positio
NXF CardFrame and NetModules 3 NetLinx Cardframe, Control Cards, and NetModules Setting the CardFrame's starting address The 8-position CardFrame Number DIP switch, located on the rear of the CardFrame (FIG. 1 on page 1), sets the starting address (the device number in the D:P:S specification) for t...
Page 10 - ) accommodate one NetLinx Control Card, and connect to the; NXS-NMS NetModules specifications; The table below lists the NXS-NMS specifications.; Mounting modules into an equipment rack; NXS-NMS NetModules Specifications; NetModule
NXF CardFrame and NetModules 4 NetLinx Cardframe, Control Cards, and NetModules NXS-NMS NetModules The NXS-NMS NetModules ( FG2009-10 ) accommodate one NetLinx Control Card, and connect to the NetLinx bus via ICSNet connections. The NetModules offer a simple and economical way to integrate additiona...
Page 11 - Installing Control Cards into an NXF CardFrame; Strip 0.25 inch of wire insulation off all wires.
NXF CardFrame and NetModules 5 NetLinx Cardframe, Control Cards, and NetModules Installing Control Cards into an NXF CardFrame 1. Remove the magnetic front faceplate/viewing window from the CardFrame. 2. Align the edge of the Control Card with a slot in the CardFrame. Slide the card into the CardFra...
Page 13 - NXC-COM2 Dual COM Port Control Card; The NXC-COM2 Dual COM Port Control Card (; Specifications; NXC-COM2 Specifications
NXC-COM2 Dual COM Port Control Card 7 NetLinx Cardframe, Control Cards, and NetModules NXC-COM2 Dual COM Port Control Card The NXC-COM2 Dual COM Port Control Card ( FG2022 ) provides two RS-232, RS-422, or RS-485 control ports and LED feedback for remote sources connected to the NetLinx CardFrame, N...
Page 14 - Pinouts and Wiring Configuration; NXC-COM2 Wiring Configuration; Pin Signal; NXC-COM2 Channel Assignment; Channe
NXC-COM2 Dual COM Port Control Card 8 NetLinx Cardframe, Control Cards, and NetModules Pinouts and Wiring Configuration NXC-COM2 Channel Assignment NXC-COM2 Pinouts NXC-COM2 Wiring Configuration Pin Signal Function RS-232 RS- 422 RS-485 1 GND Signal ground X X 2 RXD1 Receive data X 3 TXD1 Transmit d...
Page 15 - NXC-COM2 Programming Information; Command; CHARDM; CTSPSH; CTSPSH OFF
NXC-COM2 Dual COM Port Control Card 9 NetLinx Cardframe, Control Cards, and NetModules NXC-COM2 Programming Information NXC-COM2 Send_Commands NXC-COM2 Send_Commands Command Description B9MOFF Disable 9-bit in 232/422/455 mode. This command works in conjunction with the B9MON command.Syntax: SEND_CO...
Page 23 - Setting the Switch/Voltage Mode Jumpers; Open mode setting
NXC-I/O10 Input/Output Control Card 17 NetLinx Cardframe, Control Cards, and NetModules Setting the Switch/Voltage Mode Jumpers The NXC-I/O10 responds to switch closures or voltage-level (high/low) changes. Compatible I/O devices include the Power Control Sensor (PCS), tape transports and limit swit...
Page 25 - ) provides four IR/Serial input control ports with LED; NXC-IRS4 Specifications
NXC-IRS4 4-Port IR/S Control Card 19 NetLinx Cardframe, Control Cards, and NetModules NXC-IRS4 4-Port IR/S Control Card The NXC-IRS4 4-Port IR/S Control Card ( FG2023 ) provides four IR/Serial input control ports with LED status feedback. Each port in the NXC-IRS4 stores programmed commands for IR- ...
Page 26 - NXC-IRS4 Channel Assignments; CAROFF
NXC-IRS4 4-Port IR/S Control Card 20 NetLinx Cardframe, Control Cards, and NetModules Pinouts, Signals, and Functions NXC-IRS4 Channel Assignments The NXC-IRS4 channel settings listed in the following table set the IR output channels. The NXC-IRS4 can process up to two IR or serial device channel se...
Page 27 - CP; CTON
NXC-IRS4 4-Port IR/S Control Card 21 NetLinx Cardframe, Control Cards, and NetModules NXC-IRS4 Send_Commands (Cont.) Command Description CH Send IR pulses for the selected a channel. All channels below 100 are transmitted as two digits. If the IR code for ENTER (function #21) is loaded, an Enter wil...
Page 28 - IROFF; POD
NXC-IRS4 4-Port IR/S Control Card 22 NetLinx Cardframe, Control Cards, and NetModules NXC-IRS4 Send_Commands (Cont.) Command Description GET MODE Poll the IR/Serial port's configuration parameters and report the active mode settings to the device requesting the information. The port responds with: &...
Page 29 - PTOF; PTON
NXC-IRS4 4-Port IR/S Control Card 23 NetLinx Cardframe, Control Cards, and NetModules NXC-IRS4 Send_Commands (Cont.) Command Description PON Turn ON a device connected to an IR port based on the status of the corresponding I/O Link input. If at any time the IR sensor input reads that the device is O...
Page 30 - SP; XCH
NXC-IRS4 4-Port IR/S Control Card 24 NetLinx Cardframe, Control Cards, and NetModules NXC-IRS4 Send_Commands (Cont.) Command Description SET INPUT LINK Sets an IR device to link to an input channel for use with 'PON' and 'POF' commands. The input channel is used for power sensing (via a PCS). Sets a...
Page 33 - NXC-REL10 Relay Control Card; ) provides ten relays that support devices that employ simple; NXC-REL10 Specifications; Pin Function
NXC-REL10 Relay Control Card 27 NetLinx Cardframe, Control Cards, and NetModules NXC-REL10 Relay Control Card The NXC-REL10 Relay Control Card ( FG2020 ) provides ten relays that support devices that employ simple momentary or latching contact-closure control, with LED feedback. FIG. 6 shows the REL...
Page 35 - NXC-VAI4 Analog Voltage Control Card; The NXC-VAI4 Analog Voltage Control Card (; NXC-VAI4 Specifications
NXC-VAI4 Analog Voltage Control Card 29 NetLinx Cardframe, Control Cards, and NetModules NXC-VAI4 Analog Voltage Control Card The NXC-VAI4 Analog Voltage Control Card ( FG2025 ) provides four independent analog-to-digital inputs and four independent digital-to-analog outputs, which are controllable ...
Page 36 - Pinouts and Functions
NXC-VAI4 Analog Voltage Control Card 30 NetLinx Cardframe, Control Cards, and NetModules Pinouts and Functions NXC-VAI4 Specifications (Cont.) I/O Status LEDs 1-8: (two LEDs per channel) LEDs light to indicate ON status. • 4 yellow LED's (one per channel) light to indicate input signal changes repor...
Page 37 - Channel Assignments; NXC-VAI4 Channel Assignments; Channel
NXC-VAI4 Analog Voltage Control Card 31 NetLinx Cardframe, Control Cards, and NetModules Channel Assignments The channel ON/OFF assignments for the NXC-VAI4 are described in the following table. Off = 50% voltage, and all channel assignments are mutually exclusive. NXC-VAI4 Channel Assignments Chann...
Page 39 - NXC-VAI4 Output Level Assignments; Leve
NXC-VAI4 Analog Voltage Control Card 33 NetLinx Cardframe, Control Cards, and NetModules NXC-VAI4 Output Level Assignments NXC-VAI4 Output Level Assignments Leve l Description 1 8 bit field; sets voltage on Output 1 to the value commanded.The range is 0-255.Conflicts with channels 1, 5, 10, 14, 18, ...
Page 40 - NXC-VAI4 Input Level Assignments; Level Description; DEFAULT ALL
NXC-VAI4 Analog Voltage Control Card 34 NetLinx Cardframe, Control Cards, and NetModules NXC-VAI4 Input Level Assignments Programming Information These NetLinx Send_Commands control the NXC-VAI4: NXC-VAI4 Input Level Assignments Level Description 1 8 bit field, returns the current output voltage cod...
Page 44 - PR
NXC-VAI4 Analog Voltage Control Card 38 NetLinx Cardframe, Control Cards, and NetModules NXC-VAI4 Send_Commands (Cont.) Command Description PN Sets the value of either the minimum output voltage allowed for an output, or the minimum position voltage expected for an input.· Voltage settings are round...
Page 45 - PZ
NXC-VAI4 Analog Voltage Control Card 39 NetLinx Cardframe, Control Cards, and NetModules NXC-VAI4 Send_Commands (Cont.) Command Description PX Sets the value of "I/O <x> MAXIMUM" which is either the maximum output voltage allowed for an Output, or the maximum position voltage expected ...
Page 47 - NXC-VOL4 Volume Control Card; ) provides four discrete volume control channels with LED; NXC-VOL4 Specifications
NXC-VOL4 Volume Control Card 41 NetLinx Cardframe, Control Cards, and NetModules NXC-VOL4 Volume Control Card The NXC-VOL4 Volume Control Card ( FG2024 ) provides four discrete volume control channels with LED feedback. The volume control channels can be programmed for mono or stereo operation, and ...
Page 49 - NXC-VOL4 Channel Assignments; channel
NXC-VOL4 Volume Control Card 43 NetLinx Cardframe, Control Cards, and NetModules NXC-VOL4 Connections/Wiring The NXC-VOL4 card contains four audio volume control channels. Each line-level channel is isolated from system ground and can be configured for balanced or unbalanced line operation. It suppo...
Page 50 - Level
NXC-VOL4 Volume Control Card 44 NetLinx Cardframe, Control Cards, and NetModules NXC-VOL4 Levels Volume (audio) channels 1 and 2 use levels 1 and 2 respectively. For reading current volume levels and displaying bargraphs see CREATE_LEVEL and SEND_LEVEL . The two levels associated with each port of t...
Page 51 - Programming Information
NXC-VOL4 Volume Control Card 45 NetLinx Cardframe, Control Cards, and NetModules Programming Information These NetLinx Send_Commands control the NXC-VOL4. NXC-VOL4 Send_Commands Command Description PL Ramps specified (audio) channel(s) from current level to a specified preset level or percentage at ...