American Standard 6067.22X - Manuals

Page 2 - UNPACKING; DO NOT REMOVE PROTECTIVE FILM FROM SENSOR; CLOTH WITH A COARSE SURFACE.

All American Standard Products Are Water Tested At Our Factory. Some Residual Water May Remain In The Valve During Shipping. Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instruction...

Page 3 - PRIOR TO INSTALLATION; Prior to installing the SelectronicTMFlush Valve; See Step 4; and debris can cause flush valve to run continuously.; Roughing-in Dimensions; Concealed Flushometer; a b ove fi x t u re. Co n s u l t Co d e s fo r d e ta i l s.

RECOMMENDED TOOLS; Fig. 2 Fig. 2 1. 2.3.4.5.6. 7. 8.9. 10. Teflon Tape Flat Blade ScrewdriverAdjustable Wrench Tape Measure HacksawTubing CutterFileFor Sweat Connection; Solder and Torch2.5mm Hex Wrench1.5mm Hex Wrench 1 2 3 4 5 6 7 9 10 8 PRIOR TO INSTALLATION Note: Prior to installing the Selectro...

Page 4 - CAUTION; install Sweat Solder Adapter; C LO C K W I S E

Fig. 4 Fig. 3a Fig. 5 3 INSTALL ELECTRICAL BOXASSEMBLY; Fig. 3 1. Cut a 127x127mm (5"x 5") opening in finished wall for ELECTRICAL BOX (1) at the deminsion shown in Fig.3. 2. Rotate the 4 MOUNTING TABS (2) flat against the electrical box. Holding the MOUNTING TABS (2) in position install the...

Page 5 - TOP SPUD

4 Fig. 6 Fig. 6a Fig. 6b Fig. 6c 3 4 INSTALL VACUUM BREAKER ANDFLUSH CONNECTIONS; Fig. 6 4 1. Place the SPUD FLANGE (1) over the spud on the Fixture. Fig. 6. 2. Thread SPUD COUPLING NUT (2) onto Spud. Make sure SEAL WASHER (4) and FRICTION WASHER (3) are installed. Do not tighten fully. Fig. 6. 3 . ...

Page 8 - If FRONT PANEL

T O P 1. Remove the four COVER SCREWS (1) and COVER (2) from ELECTRICAL BOX (3) . Fig. 10. 2. Install BATTERY (4) into holder on DC circuit board. Press BATTERY (4) down (contacts facing downward) into position until tabs lock BATTERY (4) into place. 3. Attach the SAFETY CHAIN (5) from the FRONT PAN...

Page 10 - SENSOR WIRE

FOR AC-VERSION(MULTI HOOK-UP); Fig. 15, 15a Unit #1 Unit #1 Unit #2 Unit #3 1 . Remove the COVER SCREWS (1) and COVER (2) from each ELECTRICAL BOX (3) . 2. See AC Version Electrical Hook-up for Unit #1 of the Multi hook-up. 3. Install SENSOR WIRE GROMMET (4) and FLUSH VALVE SENSOR WIRE (5) into the ...

Page 11 - C O U N T E R - C LO C K W I S E; NOTE: Stand outside of sensor detection aera.

3 5 7 6 T O P 1. Remove FRONT PANEL. For removing front panel see Step 9 for instructions . 2. Remove the four COVER SCREWS (1) and COVER (2) from ELECTRICAL BOX (3) . Fig. 16. 3. Disconnect GREY SENSOR WIRE (4) from CIRCUIT BOARD (5) . 4. Remove CIRCUIT BOARD (5) from ELECTRICAL BOX (3) . Fig. 16a....

Page 12 - Stand outside of sensor detection aera.

6 T O P 11 Note: The detection distance is preset and is ideal for most installations. Should an adjustment be required follow the steps below. 1. Remove FRONT PANEL (1) . See Step 9 for removing front panel instructions . 2. Remove the four COVER SCREWS (2) and COVER (3) from ELECTRICAL BOX (4) . F...

Page 14 - MODEL NUMBERS

S E L E C T R O N I C ™ P R O X I M I T Y T O I L E T C O N C E A L E D F L U S H VA LV E 1 . 2 8 & 1 . 6 G P F 13 A950223-0071600A SENSOR FOR FLUSH VALVE WITH 1.6 gpf A950223-0071280A SENSOR FOR FLUSH VALVE WITH 1.28 gpf A923654-0070A BATTERY 6VCR-P2 M962664-0070A SOLENOID ASSEMBLY M962663-0070...