American Audio Vplus Series - Manuals

Page 2 - NO SE ABRA

This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user of the presence of important operatin...

Page 3 - CAUTION; POUR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICE TO YOUR AUTHORIZED AMERICAN AUDIO ® DEALER. CAUTION Do not open - risk of electric shock FOR OPTIMUM PERFORMANCE AND RELIABILITY DO NOT PRESENT THE AMPLIFIER WITH A S...

Page 4 - plus

Important Precautions • To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture• Do not spill water or other liquids into or on to your unit• Do not attempt to operate this unit if the power cord has been frayed or broken• Do not attempt to remove or break off the gr...

Page 5 - FRONT PANEL; CONTROLS AND FUNCTIONS

FRONT PANEL 1. Power Switch - This switch controls the units main power. 2. Channel 1 Limiter Switch (V2000 & V3000 Only) - This is used to activate the channels built-in limiter. The limiter reduces the average output level when the signal begins to distort, this process is designed to reduce d...

Page 6 - REAR PANEL; Connect your channel two speakers to channel two output.

V1000 plus REAR PANEL 1. Channel 2 Input - Connect the input source for channel two to either the balance XLR or the balanced/unbalanced 1/4” input jacks. The 1/4” TRS plug is configured as follows; Tip is positive, Ring is negative and Sleeve is ground. The XLR jack is configured as follows; Pin th...

Page 9 - Set Up; INPUTS; US ITT Standard

OUTPUTS: Binding Post/Banana Plug - Connect your speakers to the binding post outputs on the rear of the amplifier. The speaker wire may be connect by bare wire (directly connected, usually for permanent connections), banana plug, or spade connector. Connections are made to Channels 1 and 2 output’s...

Page 11 - TYPICAL MONO BRIDGE SET-UP; OHM MINIMUM; SPEAKERS; OHM MINIMUM; SPEAKERS; OHM MINIMUM

TYPICAL MONO BRIDGE SET-UP SPEAKERS 8 OHM MINIMUM Typical Stereo Output Connections Diagram 14 Diagram 13 SPEAKERS 4 OHM MINIMUM SPEAKERS 4 OHM MINIMUM 1000 WATTS BRIDGE MONO 120V~60Hz 6 A M P CAUTION 4 OHMS MINIMUM IMPEDANCE PRE CHANNEL 4 OHMS MINIMUM IMPEDANCE IN MONO BRIDGE MODE OUTPUT INPUT CH 1...

Page 12 - Typical Stereo Set-Up; Typical Mixer

12 34 Typical Stereo Set-Up Typical Mixer V3000 plus series (Rear View) Typical SpeakerConnect to Vplus series Channel One Output Typical SpeakerConnect to Vplus series Channel Two Output Diagram 15 American Audio ® - www.americandj.com - V plus Series Amplifiers Power Amplifier User Manual Page 12

Page 14 - RF; from the output and

goes into protect mode, the other side will continue to operate normally. During short circuit protection, the "Clip" LED and “Protect" LED will light simultaneously indicating amplifier fault. All channel output during the “Short Circuit Protection" will be interrupted (i.e. no soun...

Page 15 - V-SERIES AMPLIFIER SPE CIFICATIONS

Output Power: 2 ohms, 1 khz 1% THD 4 ohms, 1khz, 1% THD 8 ohms, 1khz 1% THD (Bridge Mode, mono) 4 ohms, 1khz, 1% THD 8 ohms, 1khz, 1% THD Dimensions & Weight: Height Width Depth WeightFrequency Response: +/- 1db, 1w RMS. 8 ohms +/- 0.2 db, @ rated output, 8 ohms Hum & Noise: Below rated outp...