Page 2 - Jeep Wrangler; UNLIMITED JL; Warning
Jeep Wrangler UNLIMITED JL z 2/11 Types of Precautions Forbidden Indicates actions that are forbidden (must not be performed) Forbidden Indicates that disassembly is forbidden. Mandatory Indicates actions that are mandatory (must be performed) Marks content that should receive your full attention. W...
Page 3 - Tools Required
Jeep Wrangler UNLIMITED JL z 3/11 Tools Required Panel Removal Tool Sockets Phillips Screwdriver 7mm 10mm Wire Cutters Extension Ratchet T50 Torx Cordless Power Drill Cordless Impact Gun Accessory List Amplifier Assembly T-Harness Main Harness (10) Cable Ties RCA Adapters Power Cable Front Top Dash S...
Page 4 - Factory Equipment Removal Process
Jeep Wrangler UNLIMITED JL z 4/11 1 Use a panel removal tool to release (2) clips on the top of the plastic knee cover and remove it. 3 Extract (2) 7mm/Phillips screws on the bottom of the radio bezel. 5 Extract (4) 7mm/Phillips screws from the factory radio, disconnect and remove it. 2 Use a panel ...
Page 5 - Factory Equipment Removal Process (continued); Front of Vehicle
Jeep Wrangler UNLIMITED JL z 5/11 Factory Equipment Removal Process (continued) 7 Extract (4) T50 Torx Screws from the passenger side seat. 9 Using a panel removal tool, release the clips on the top dash speaker grilles and remove them. 8 Tilt the passenger seat towards the back to reveal (2) connec...
Page 6 - Installation; Note: seal the grommet; factory ground stud below the center console.
Jeep Wrangler UNLIMITED JL z 6/11 Installation 1 Connect the power cable to the Positive (+) battery terminal and route the cable down towards frame of the vehicle. Note: The Negative (-) terminal should remain disconnected until the installation is completed. 3 Route the Positive (+) power cable th...
Page 7 - Connect the main harness to the amplifier assembly; Connect the T-harness and main harness to the
Jeep Wrangler UNLIMITED JL z 7/11 Installation (continued) 7 Connect the main harness to the amplifier assembly and align it to the seat mounting holes. Front of Vehicle 9 Connect the T-harness and main harness to the radio. Refer to page 8, 9 or 10 for the corresponding system wiring diagram. 11 Ret...
Page 8 - OEM Head Unit Wiring Diagram; POWER PACK AMPLIFIER KTP-445U; To Vehicle Connectors; ADAPTER
Jeep Wrangler UNLIMITED JL z 8/11 OEM Head Unit Wiring Diagram L R Amplifier Speaker Wiring CH 1 - White (+) White/Black (-)CH 2 - Gray(+) Gray/Black (-)CH 3 - Green (+) Green/Black (-)CH 4 - Purple (+) Purple/Black (-) NOTE: FOR BEST PERFORMANCE SET AMPLIFIER AND SUBWOOFER TO RECOMMENDED SETTINGS A...
Page 9 - Aftermarket Head Unit Wiring Diagram
Jeep Wrangler UNLIMITED JL z 9/11 Aftermarket Head Unit Wiring Diagram L R BROWN/ORANGE RCA Adapter Amplifier Speaker Wiring CH 1 - White (+) White/Black (-)CH 2 - Gray(+) Gray/Black (-)CH 3 - Green (+) Green/Black (-)CH 4 - Purple (+) Purple/Black (-) NOTE: FOR BEST PERFORMANCE SET AMPLIFIER AND SU...
Page 10 - Alpine Restyle Head Unit Wiring Diagram
Jeep Wrangler UNLIMITED JL z 10/11 Alpine Restyle Head Unit Wiring Diagram To Vehicle Connectors iDatalink MAESTRO Module To OBDII Connector Power/Speaker 52-pin Black Connector Front Rear Rear Front L R L R L R Front Rear Subwoofer Blue Amp Turn-on To Vehicle’s Battery POSITIVE (+) Terminal L R For...
Page 11 - Troubleshooting Guide; Symptom
Jeep Wrangler UNLIMITED JL z 11/11 Troubleshooting Guide Symptom Possible Cause Remedy 1 System will not turn on Missing or blown fuse at the battery Insert or replace fuse Radio’s Remote Turn-On wire may be disconnected. Verify that Remote Turn-On wire is connected. 2 Volume is too loud with afterm...
