Allstar MVP-SQ - Manuals

FRONT MOUNTING BRACKET MUST BE INSTALLED TO A STRUCTURAL SUPPORT (STUD) ON THE HEADER WALL. FAILURE TO DO SO COULD CAUSE SENSING SYSTEM TO MALFUNCTION, RESULTING IN ENTRAPMENT, INJURY OR DEATH. REINFORCE HEADER IF NECESSARY USING A 2 x 6 AND LAG SCREWS (NOT PROVIDED). WARNING STEP 1: Mounting the Fr...

FIBERGLASS, ALUMINUM OR LIGHTWEIGHT STEEL GARAGE DOORS WILL REQUIRE REINFORCEMENT BEFORE INSTALLATION OF DOOR MOUNTING BRACKET. CONTACT YOUR DOOR MANUFACTURER FOR A REINFORCEMENT KIT OR INSTRUCTIONS. CAUTION! DOOR ARM CONNECTION AND INSTALLATION NOTE: If the door is of light construction it is neces...

STEP 9 : Consult the label on the rear panel of the Opener to determine its proper working voltage. Normally it will be marked for 115V, 60 cycle operation. (If it is an export model designed for 220V, 50 cycle operation, the label will clearly indicate this.) The Opener must be plugged into a prope...

INSTALLATION OF A STANDARD WALL PUSH BUTTON If desired, a standard wall push button may be installed and connected to your operator. A standard wall push button is not included in your hardware package, it can be purchased from your professional installing dealer or a door bell button [without light...

STEP 4: Run the wire from the Super Station to the opener, supporting it at 18” intervals with suitable staples. Leave a sufficient length to make the necessary connections to the opener terminal strip. WARNING: SOME LOCAL BUILDING CODES DO NOT ALLOW SURFACE WIRING. BE SAFE AND CHECK WITH THE LOCAL ...

INSTALLATION OF 2 WIRE SAFE FINISH PHOTOSYSTEM STEP 1: Mark the position of the SAFE FINISH™ Photosystem as follows: Mark a line on the left and right door jamb (close to the door track) FOUR (4) inches AND SIX (6) inches above the floor. The top mark is the maximum height and the bottom line is the...

F. Using two (2) wire nuts (supplied), connect the wire ends at the SAFE FINISH™ Photosystem receiver to the pigtail wire ends coming out of the receiver unit. Although not required, it is recommended to connect the trace wire ends together and the unmarked wire ends together. STEP 4 : Final Install...

• NEVER LET CHILDREN OPERATE OR PLAY WITH DOOR CONTROLS. KEEP THE REMOTE CONTROL AWAY FROM CHILDREN. • ALWAYS KEEP A MOVING DOOR IN SIGHT AND KEEP PEOPLE AND OBJECTS AWAY FROM THE DOOR AREA UNTIL THE DOOR IS COMPLETELY CLOSED. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR. • NEVER GO UNDER A STOPPED...

Down force adjustments are correct, the door will reverse within two seconds of contacting the object and travel to the Full Open position. If this does not occur, recheck the Limit Adjustments (Step 1, previous) and Sensitivity Adjustments (Step 2 & 3, previous. NOTE: Any time adjustments are m...

Wiring Diagram 110796 2. Close Pushbutton — Green-backlighting, arrow pointing down. Used to start the door downward. This button has no effect on a door in motion. Will allow constant pressure close operation if the photocell is misaligned. 3. Stop Button - Red-backlighting, universal “STOP” within...

Y ou r R esid en ti a l Ga r a ge D oor O p en er is fu rn ish ed with an en hanc ed 2 W i r e Saf e Fi nish™ P h ot osystem. Th e f eatu r es incl ud e: T i m e -S a v in g E l ec t r i c al C o n ne c t i o n s . N o sc rew termi n al s! Just st rip th e ends of t h e w i r es b ac k 5 /1 6 i nc h...

1 2 3 4 5 6 7 8 9 Plus Button Zero Button Minus Button IF DESIRED, RECORD YOUR RADIO TRANSMITTER CODE POSITION SETTINGS HERE See Page 11 for Radio System programming instructions and FCC/RSS-210 Industry Canada statement. The opener radio system is HomeLink® compatible. Serial #: Date Installed: You...