Allstar 831E - Manual
Allstar 831E – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – FOLLOW LOCAL BUILDING AND ELECTRICAL CODES.; BEFORE WIRING PERMANENTLY.; WARNING; YOUR OPERATOR FOR MORE DETAILS.; WARNING; 31E COMMERCIAL RECEIVER WIRING INSTRUCTIONS; STOP; RECEIVER
- Page 3 – COMMERCIAL RECEIVER & TRANSMITTER CODING INSTRUCTIONS
- Page 4 – TROUBLESHOOTING NOTES; Check code switch settings.; Manufacturer’s Limited Warranty
Page 1 of 4
P/N 106547 REV D
831E COMMERCIAL
RECEIVER
INSTRUCTIONS
MODELS:
•
831E
•
831E MASTER & SLAVE UNITS
READ THIS MANUAL CAREFULLY
BEFORE BEGINNING INSTALLATION
Allstar 831E Commercial Receivers are designed to work with most commercial door operators. The 831E is connected to the
commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. The
receiver is powered from the operator’s 24 VAC transformer. The antenna is removable and may be moved (using coaxial cable) to a
new location for better RF reception. When receivers have to be installed in close proximity to each other (such as Fire Stations),
master/slave units may be used to reduce the potential for receiver cross-talk.
•
ALLSTAR 831E RECEIVERS ARE INTENDED FOR
USE WITH COMMERCIAL DOOR OPERATORS
ONLY. DO NOT USE FOR ANY OTHER PURPOSE.
DO NOT MODIFY IN ANY MANNER.
•
CHECK LOCAL BUILDING AND ELECTRICAL
CODES FOR MANDATORY INSTALLATION AND
WIRING REQUIREMENTS.
•
CONNECT POWER CORDS ONLY TO A PROPERLY
GROUNDED OUTLET. IF PERMANENT WIRING IS
REQUIRED BY CODES, DISCONNECT POWER AT
FUSE BOX OR CIRCUIT BREAKER BEFORE
ATTEMPTING ANY WIRING CONNECTIONS.
•
DO NOT WEAR RINGS, WATCHES OR LOOSE
CLOTHING WHILE INSTALLING OR SERVICING
GARAGE DOOR OPENERS. WEAR SAFETY
GOGGLES OR OTHER PROTECTIVE EYEWEAR.
•
AN UNBALANCED DOOR OR ONE THAT STICKS OR
BINDS MAY CAUSE INJURY OR DEATH. ENSURE
DOOR IS PROPERLY BALANCED AND ELIMINATE
ANY STICKING OR BINDING.
•
YOUR GARAGE DOOR IS A LARGE MOVING
OBJECT. THE SPRINGS, PULLEYS, CABLES AND
MOUNTING HARDWARE UTILIZED TO BALANCE
ITS OPERATION ARE UNDER EXTREME TENSION
AT ALL TIMES AND CAN CAUSE SERIOUS
PERSONAL INJURY, EVEN DEATH, IF DISTURBED.
ONLY A QUALIFIED SERVICE PERSON SHOULD
MOVE, LOOSEN OR ADJUST DOOR SPRINGS OR
HARDWARE.
•
LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT
OF THE DOOR AND AWAY FROM THE MOVING
PARTS OF THE DOOR. INSTALL ENTRAPMENT
WARNING LABEL NEXT TO THE CONTROL
PUSHBUTTON IN A PROMINENT LOCATION.
•
REMOVE ALL ROPES AND REMOVE OR MAKE
INOPERATIVE ALL LOCKS CONNECTED TO THE
GARAGE DOOR.
•
T H E I M P O R T A N T S A F E G U A R D S A N D
INSTRUCTIONS IN THIS MANUAL CANNOT COVER
ALL POSSIBLE CONDITIONS AND SITUATIONS. IT
MUST BE UNDERSTOOD THAT COMMON SENSE
AND CAUTION MUST BE EXERCISED BY THE
PERSON(S) INSTALLING, MAINTAINING AND
OPERATING THIS EQUIPMENT.
INSTALLER: Leave this manual with your customer upon completion of the installation.
WARNING
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS!
PRODUCT FEATURES
IMPORTANT INSTALLATION NOTES
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 of 4 P/N 106547 REV D The 831E receiver functions as a 3-button station. Three sets of isolated contacts are provided; normally open contacts for the OPEN PUSHBUTTON (orange wires); normally open contacts for the CLOSE PUSHBUTTON (black wires); normally closed contacts for the STOP PUSHBUTTON...
Page 3 of 4 P/N 106547 REV D The 831E receiver may be used with many different Allstar transmitters. The information below indicates how to set the coding switches in the various transmitters and the 831E receiver. I F YOU ARE USING A 8831 OCS - ECONOMY OR 831 STANDARD TRANSMITTER : Exactly match al...
Page 4 of 4 P/N 106547 REV D TROUBLESHOOTING NOTES If you experience problems with the 831E Receiver, try some of the suggestions listed below before calling the Factory Technicians. R ECEIVER APPEARS DEAD ; THERE IS NO RESPONSE WHEN TRANSMITTER BUTTONS ARE PUSHED . Check the power connections to th...
