Allstar MJ5011S - Manuals

TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS! WARNING ♦ Install only on a properly balanced garage door. An improperly balanced door could cause severe injury. Have a qualified service person make repairs to cables, spring assemblies and other hardware ...

SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEATH IF DISTURBED. DO NOT ATTEMPT ADJUSTMENT. F igure 4, page 7 illustrates several positions suitable for mounting the operator; right hand or left ...

CHAIN HOIST AND FLOOR DISCONNECT INSTALLATION I f the operator is furnished with a chain hoist (Model MH5011S), pass the hand chain over the chain wheel and through the chain guides on the operator clutch shaft (opposite end from the large pulley). Fasten the ends of the chain together by opening an...

A - REVERSE CUTOUT LIMIT SWITCH B - OPEN LIMIT SWITCH C - OPEN LIMIT NUT D - LIMIT NUT RETAINING BRACKET E - REVERSE CUTOUT LIMIT NUT F - “V” BRACKET SETTING THE LIMIT SWITCHES 1) With the cover open on the electrical enclosure, reference Figure 6 below. There are two (2) switches (A and B) mounted ...

INSTALLATION INSTRUCTIONS - ELECTRICAL WIRING TO AVOID DAMAGE TO DOOR AND OPERATOR ENSURE ALL DOOR LOCKS ARE DISABLED. USE AN INTERLOCK SWITCH IF A LOCK IS REQUIRED TO RETAIN FUNCTIONALTY. CAUTION RISK OF ENTRAPMENT THAT MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE OPENER ...

DOOR EDGE INSTALLATION & WIRING Figure 8 11 OPEN TB1 STOP CLOSE OPEN COM CL OS E STOP NO REV NC REV PH O T O COM SI NGLE IL OCK 24 V A C COM SAFE FINISH PHOTOBEAM 3-WIRE PHOTOBEAM MOTOR CONTROL BOARD Door Edge and Photoelectric Wiring Figure 9 See text on page 10 for operation when Safe-Finish™ ...

INSTALLATION INSTRUCTIONS 12 Figure 10 NOTE: It is now necessary to turn on the power in order to to change the Operating Mode (if applicable), program any changes desired to the operator’s other settings, check for proper operation, and finalize any adjustments to include the limit settings. Before...

OPERATION & ADJUSTMENT INSTRUCTIONS 14 CLUTCH ADJUSTMENT The clutch serves to protect the door, the electric operator and other equipment from undue stress or damage caused by starting forces and/or an obstruction to the door. It should be set no tighter than is necessary to smoothly and consist...

OPERATION & ADJUSTMENT INSTRUCTIONS 15 BRAKE ADJUSTMENT Figure 14 Brake Adjustment The brake is adjusted at the factory and may need periodic adjustment for wear. When adjustment becomes necessary see Figure 14 at right for the adjustment procedure. Changing the Switch Selectable Operation Modes...

OPERATION AND ADJUSTMENT INSTRUCTIONS 16 B2 Operation Open Button : Momentary activation; open override of closing door. Close Button : Momentary activation. Stop Button : Momentary activation; stops open, close or reverse action. Single Button : Momentary activation to open; open override of closin...

OPERATION & ADJUSTMENT INSTRUCTIONS 17 Setup Modes Various operating characteristics can be modified via the setup modes. The operator is moved to the close limit position and the on-board dip switches (see Figure 15) are TEMPORARILY set according to the table at right to enter a Setup Mode. The...

OPERATION AND ADJUSTMENT INSTRUCTIONS 18 Following installation, the operator MUST be tested and respond correctly to all controls as specified on the wiring diagram. KEEP personnel and equipment clear of the area beneath the door when performing the tests. When testing the 3-button wall station, fi...

WIRING DIAGRAM 19 C D O M C B 2 005 EDGE RADIO c. p. ALLSTAR C O RP . P4 24V S1 R58 R56 R55 R54 R45 R46 R53 PC B 11269 5 R E V B T S L K K2 K4 K3 K5 K6 CO M OL S CL S CO M HIGH VOLTAGE OPE N MO4 MO3 MO2 MO1 ILK 24V COM VCC FRA COM 24V RM1 RM2 RM3 VCC COM P7 R8 R24 C12 TB1 STATUS LD4 OFF S4S3S2S1 C25...

Manufacturer’s Limited Warranty Linear LLC warrants its Allstar brand commercial door operators to be free from defect in material and workmanship for a period of two (2) years from the date of purchase. To obtain service contact your dealer. To obtain service under this warranty the buyer must obta...