Allied Telesis 86241-06 - Manuals

Page 2 - Level: 2

2 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E Features in 86241-06 Patch 86241-06 includes all issues resolved and enhancements released in previous patches for Software Release 2.4.1, and the following enhancements: When more than two firewall policies were conf...

Page 6 - Patch file details are listed in Table 2:; Network affecting: No

6 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E Features in 86241-05 Patch file details are listed in Table 2: Patch 86241-05 includes all issues resolved and enhancements released in previous patches for Software Release 2.4.1, and the following enhancements: Supp...

Page 7 - The debugging commands are:; Patch file details are listed in Table 3:

Patch 86241-06 For Rapier Switches 7 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E Debugging commands are now available for the RADIUS and TACACS control protocols. Raw packets, decoded packets, and errors can now be displayed. Access control packet debugging allows the contents of th...

Page 11 - Patch file details are listed in Table 2.

Patch 86241-06 For Rapier Switches 11 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E Some change actions, and the resending of prune messages were not operating correctly. This issue has been resolved. The ADD FIREWALL POLICY and SET FIREWALL POLICY commands did not generate a valid po...

Page 12 - The following issues have been resolved:

12 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E After an ASYN port test, the port is now reset to its pre-test state if the test was started by a user connected to the same ASYN port. The following issues have been resolved: • When equal paths exist to a source, a...

Page 13 - Patch file details are listed in Table 5:

Patch 86241-06 For Rapier Switches 13 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E If multiple IPv6 interfaces shared the same link-local address, pings to the link-local address sometimes failed. This issue has been resolved. The source net mask has been removed from DVMRP prune, gr...

Page 22 - DS3 Interfaces; B3ZS line encoding

22 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E but is now checked by ICMP handlers for attacks and eligibility. If the ICMP traffic matches a NAT rule, NAT will occur on inbound and outbound traffic. HTTP 1.0 requests sometimes caused the firewall HTTP proxy to c...

Page 24 - Loopbacks

24 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E The three C-bits in M-subframe 4 are designated as FEBE bits. The FEBE bits are returned to the far end to indicate the occurrence of a framing error or CP-bit parity error. If none occur, the FEBE bits are set to al...

Page 25 - DS3 Configuration

Patch 86241-06 For Rapier Switches 25 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E Diagnostic loopback is shown in Figure 3 on page 25. In this loopback mode the transmit signal is connected straight to the receive signal. Figure 3: Diagnostic Loopback. In C-bit parity mode it is als...

Page 27 - instance is the number of the DS3 interface.

Patch 86241-06 For Rapier Switches 27 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E The PARAM24 parameter specifies the 24-hour counter threshold for all performance monitoring parameters (PES, PSES, SEF, UAS, LES, CES, CSES) between 1 and 65535 seconds inclusive. If a trigger has bee...

Page 29 - Dynamic Port Security

Patch 86241-06 For Rapier Switches 29 Patch 86241-05 for Software Release 2.4.1C613-10340-00 REV E Dynamic Port Security Dynamic Port Security allows for dynamic MAC address learning on a switch port. If a MAC address is unused for a period of time, it will be aged from the database of currently acc...

Page 30 - Availability; licence or password is not required to use a patch.; or not

30 Patch Release Note Patch 86241-05 for Software Release 2.4.1 C613-10340-00 REV E Figure 1-7: Example output from the SHOW SWITCH PORT command showing the RELEARN parameter. Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www.alliedtelesyn.co...