Allied Telesis 86222-27 - Manuals

Page 2 - Enable and Disable ICMP Messages

2 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Features in 86222-27 Patch 86222-27 includes all issue...

Page 6 - Patch Release Note

6 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z The GBLIP parameter in the ADD FIREWALL POLICY RULE ACTION=NONAT command is optional. However, if the command was executed without the GBLIP parameter set, the command erroneously failed after a CREATE CONFIGURATION c...

Page 7 - Some issues with DVMRP forwarding have been resolved.

Patch 86222-27 For Rapier Switches 7 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z one of these servers did not exist, or the UDP session had failed to open. This issue has been resolved. If all 32 VLAN interfaces had IP addresses attached, only 31 VLANs could be multihomed. Now all 3...

Page 9 - Network affecting: No

Patch 86222-27 For Rapier Switches 9 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z Features in 86222-24 Patch file details are listed in Table 4: Patch 86222-23 includes all issues resolved and enhancements released in previous patches for Software Release 2.2.2, and the following enh...

Page 12 - Base Software Release File

12 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z When OSPF was enabled on startup, an OSPF interface would sometimes stay in the DOWN state. This issue has been resolved. Logging out from a Telnet session caused the switch to restart. This issue has been resolved. ...

Page 33 - MD5 Authentication now works correctly with RIP packets.

Patch 86222-27 For Rapier Switches 33 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z A watchdog timout occurred when the router received an HTTP message with an over-length header. Normal HTTP requests would also occasionally cause watchdog timeouts. These issues have been resolved. Th...

Page 40 - Internet Control Message Protocol; Network Unreachabl; Commands; DISABLE IP ICMPREPLY; Syntax; Description

40 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z Enable and Disable ICMP Messages The Internet Control Message Protocol (ICMP) allows routers to send error and control messages to other routers or hosts. It provides the communication between IP software on one syst...

Page 41 - To disable all configurable ICMP messages, use the command:; ENABLE IP ICMPREPLY; ENABLE IP; SHOW IP ICMPREPLY

Patch 86222-27 For Rapier Switches 41 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z If ALL is specified, all configurable ICMP message replies are disabled. If NETUNREACH is specified, all network unreachable message replies are disabled (RFC792 Type 3 Code 0). If HOSTUNREACH is speci...

Page 42 - IGMP Snooping All-Group Entry; IGMP snooping; This enhancement modifies one command:

42 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z IGMP Snooping All-Group Entry Because IGMP is an IP-based protocol, multicast group membership for VLAN aware devices is on a per-VLAN basis. If at least one port in the VLAN is a member of a multicast group, multica...

Page 43 - Modified Command; SHOW IP IGMP; interface; This enhancement includes the line “; Disabled All-groups ports; Examples; To show information about IGMP, use the command:; See Also; Table 26: New parameter in the output of the SHOW IP IGMP command.

Patch 86222-27 For Rapier Switches SHOW IP IGMP 43 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z Modified Command SHOW IP IGMP Syntax SHOW IP IGMP [COUNTER] [INTERFACE= interface ] Description This command displays information about IGMP, and multicast group membership for each IP int...

Page 44 - New Commands; ENABLE IP IGMP ALLGROUP

44 ENABLE IP IGMP ALLGROUP Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z New Commands This enhancement request introduces two new commands from enabling/disabling all-group entries on switch ports. ENABLE IP IGMP ALLGROUP Syntax ENABLE IP IGMP ALLGROUP=[{ port-list...

Page 45 - DISABLE IP IGMP ALLGROUP; Availability; licence or password is not required to use a patch.

Patch 86222-27 For Rapier Switches DISABLE IP IGMP ALLGROUP 45 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www.alliedtelesyn.co.nz/support/updates/patches.html . A licence or pass...