Allied Telesis 86222-27 - Manual
Allied Telesis 86222-27 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Enable and Disable ICMP Messages
- Page 6 – Patch Release Note
- Page 7 – Some issues with DVMRP forwarding have been resolved.
- Page 9 – Network affecting: No
- Page 12 – Base Software Release File
- Page 33 – MD5 Authentication now works correctly with RIP packets.
- Page 40 – Internet Control Message Protocol; Network Unreachabl; Commands; DISABLE IP ICMPREPLY; Syntax; Description
- Page 41 – To disable all configurable ICMP messages, use the command:; ENABLE IP ICMPREPLY; ENABLE IP; SHOW IP ICMPREPLY
- Page 42 – IGMP Snooping All-Group Entry; IGMP snooping; This enhancement modifies one command:
- Page 43 – Modified Command; SHOW IP IGMP; interface; This enhancement includes the line “; Disabled All-groups ports; Examples; To show information about IGMP, use the command:; See Also; Table 26: New parameter in the output of the SHOW IP IGMP command.
- Page 44 – New Commands; ENABLE IP IGMP ALLGROUP
- Page 45 – DISABLE IP IGMP ALLGROUP; Availability; licence or password is not required to use a patch.
S i m p l y c o n n e c t i n g t h e w o r l d
Patch Release Note
Patch 86222-27
For Rapier Switches
Introduction
This patch release note lists the issues addressed and enhancements made in
patch 86222-27 for Software Release 2.2.2 on existing models of Rapier L3
managed switches. Patch file details are listed in Table 1.
This release note should be read in conjunction with the following documents:
■
Release Note: Software Release 2.2.2 for Rapier Switches, AR300 and
AR700 Series Routers, and AR800 Series Modular Switching Routers
(Document Number C613-10313-00 Rev A) available from
www.alliedtelesyn.co.nz/documentation/documentation.html
■
Rapier Switch Documentation Set for Software Release 2.2.1 available on
the Documentation and Tools CD-ROM packaged with your switch, or
from
www.alliedtelesyn.co.nz/documentation/documentation.html
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
Table 1: Patch file details for Patch 86222-27.
Base Software Release File
86s-222.rez
Patch Release Date
13-June-2003
Compressed Patch File Name
86222-27.paz
Compressed Patch File Size
1036828 bytes
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Features in 86222-27 Patch 86222-27 includes all issue...
6 Patch Release Note Patch 86222-27 for Software Release 2.2.2 C613-10319-00 REV Z The GBLIP parameter in the ADD FIREWALL POLICY RULE ACTION=NONAT command is optional. However, if the command was executed without the GBLIP parameter set, the command erroneously failed after a CREATE CONFIGURATION c...
Patch 86222-27 For Rapier Switches 7 Patch 86222-27 for Software Release 2.2.2C613-10319-00 REV Z one of these servers did not exist, or the UDP session had failed to open. This issue has been resolved. If all 32 VLAN interfaces had IP addresses attached, only 31 VLANs could be multihomed. Now all 3...
