AEG L 60460 FL- Manuals

Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro-tection against moisture IPX4 Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton...

4.1 Accessories 1 2 3 4 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear sideof the cabinet after the removal ofthe transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on theedge of a sink. 5. CONTROL P...

• After 5 minutes from the end of the washing programme. Refer to 'At theend of programme'. 5.2 Programme knob 2 Turn this knob to set a programme. 5.3 Display 3 A B C The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 mi-nute. • The delay start W...

6. PROGRAMMES ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Cottons 95° - Cold White and colouredcotton with normalsoil.max. 6 kg WashRinsesLong spin SPIN REDUC-TIONRINSE HOLDEXTRA RINSETIME SAVE 1) Cottons + Pre-wash 95° - Cold White and colouredcotton with heavyso...

programmes in terms of combined energy and water consumption for washing normallysoiled cotton laundry.Set this programme to have a good washing results and decrease the energyconsumption. The time of the washing programme is extended. The washing temperature of the washing phase may differ from the...

Pro- grammes Load (kg) Energy con- sump- tion (kWh) Water con- sump- tion (li- tre) Ap- proxi- mate pro- gramme dura- tion (mi- nutes) Re- main- ing mois- ture (%) 1) L 60260 FL Re- main- ing mois- ture (%) 1) L 60460 FL Re- main- ing mois- ture (%) 1) L 60660 FL Standard 40°C cotton 3 0.51 38 158 5...

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain ...

Check the position of the flap 1. Pull out the detergent dispenser un-til it stops. 2. Press the lever down to remove thedispenser. 3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn theflap down. With the flap in the positionDOWN: – Do not use gelatinous or thick liquid d...

• The door lock symbol goes off.• Press button 1 to deactivate the ap- pliance. After five minutes from theend of the programme, the energysaving function automatically deacti-vates the appliance. When you activate the applianceagain, the display show the endof the last set programme. Turnthe progra...

• Do not mix different types of deter- gents. • To help the environment, do not use more than the correct quantity of de-tergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the pro-gramme temperature ...

• Set the hottest cotton wash pro- gramme • Use a correct quantity of powder de- tergent with biological properties. After each wash, keep the door open fora while to prevent mould and to let un-pleasant smells go out. 11.4 Door seal Regularly examine the seal and removeall objects from the inner pa...

5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the recess. 11.7 Drain pump Regularly examine the drainpump and make sure that it isclean. Clean the pump if:• The appliance does not drain the wa- ter. • The drum cannot turn.• The appliance makes an unusual noise because of th...

6. Remove fluff and objects from thepump. 7. Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre. 2 1 8. Clean the filter under the water tapand put it back in the pump into thespecial guides. 9. Make sure that you tighten correctlythe filter to preve...

To clean the water inlet filters: 1. Close the water tap. 2. Remove the water inlet hose fromthe water tap. 3. Clean the filter in the inlet hose witha stiff brush. 4. Remove the inlet hose behind theappliance. 5. Clean the filter in the valve with astiff brush or a towel. 45° 20° 6. Install again t...

12. TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the table). If not, contact theservice centre. With some problems, the acousticsignals operate and the display showsan alarm code: • - The appliance does n...

Problem Possible cause Possible solution You did not remove thestubborn stains beforeyou wash the laundry. Use special products to removethe stubborn stains. Incorrect temperaturewas set. Make sure that you set the cor-rect temperature. Too much laundry load. Decrease the laundry load. After the che...

4. Remove the internal film. 5. Open the door and remove all theitems from the drum. 6. Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure not to damage the ho-ses. 1 2 7. Remove the polystyrene protecti...

13.3 Positioning and levelling x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment o...

13.4 The inlet hose 20 O 20 O 20 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rect position. • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaksfrom th...

Water-stop device A The inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in the window «A» shows thisfault .If this occur, close the water tap andcontact the service centre to replace thehose. 13.5 Water drainage There are di...

• If the end of the drain hose is this (see the drawing), you can push it directlyinto the stand pipe. Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drainhose in the spigot and tighten it with aclip. Make sure that the drain hosemakes a loop to prevent that r...

13.6 In the interest of the environment • Connect the appliance to the FOUL system for the drain water. The sew-age works keeps the drain water forthe treatment before to release safelyit into a river. Do not connect this ap-pliance to the surface drain system ofthe water because it releases the dra...

PRODUCT DESCRIPTION 1 2 3 5 6 7 4 8 10 11 12 9 1 Worktop 2 Detergent dispenser 3 Control panel 4 Door handle 5 Rating plate 6 Drain pump 7 Feet for the appliance level 8 Water drain hose 9 Water inlet valve 10 Mains cable 11 Transit bolts 12 Feet for the appliance level ACCESSORIES 1 2 3 4 1 Spanner...

CONTROL PANEL 1 2 3 4 5 6 7 8 9 1 On/Off button ( Aan/Uit ) 2 Programme knob 3 Display 4 Start/Pause button ( Start/Pauze ) 5 Delay start button ( Startuitstel ) 6 Time saving button ( Tijd Besparen ) 7 Extra rinse button ( Extra Spoelen ) 8 Spin button ( TPM ) 9 Temperature button ( Temp. °C ) ON O...

The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay starttime. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Referto 'Tr...

PROGRAMMES ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Katoen95° - Cold White and colouredcotton with normalsoil.max. 6 kg WashRinsesLong spin SPIN REDUCTIONRINSE HOLDEXTRA SPOELENTIJD BESPAREN 1) Katoen + Voor-was95° - Cold White and colouredcotton with heavy soi...

ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Gordijnen40° - Cold Set this programmeto wash curtains. Itadds automaticallythe prewash phase toclean the dust fromthe curtains.Do not put the deter-gent into the prewashcompartment.max. 2 kg PrewashWashRinsesShort spin ...

BEFORE FIRST USE 1. To activate the drain system, put 2litre of water in the main wash com-partment of the detergent dispens-er. 2. Put a small quantity of detergent inthe main wash compartment of the detergent dispenser. Set and starta programme for cotton at thehighest temperature without laun-dry...

FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase, the soak pro-gramme and for the stain function.Add the detergent for prewash, soak and stain remover beforethe start of the programme. The detergent compartment for the washing phase.If you use a liquid detergent, p...

3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn theflap down. With the flap in the positionDOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid deter- gent than the limit showed inthe flap. – Do not set the prewash phase. – Do not set the d...

CHANGE A FUNCTION You can change only some functionsbefore they operate. 1. Press button 4 . The indicator flashes. 2. Change the function set. SET THE DELAY START 1. Press button 5 again and again until the display shows the numberof minutes or hours. 2. Press button 4 , the appliance starts the co...

HINTS AND TIPS THE LAUNDRY LOAD • Divide the laundry in: white, col- oured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and col- oured items. • Some coloured items can discolour with the first wash. We recommendtha...

Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 20

CARE AND CLEANING WARNING! Disconnect the appliance from themains supply before you clean it. DESCALING The water we use contains limescale. Ifit becomes necessary, use a water soft-ener to remove limescales.Use a special product made for wash-ing machines. Obey the instructionsthat you find on the ...

DETERGENT DISPENSER To clean the dispenser: 1 2 1. Press the lever. 2. Pull the dispenser out. 3. Remove the top part of the liquidadditive compartment. 4. Clean all the parts with water. 5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the re-cess. DRAIN PUMP Regularly examin...

To clean the drain pump: 1. Open the drain pump door. 2. Put a container below the recess ofthe drain pump to collect the waterthat flows out. 3. Press the two levers and pull for-ward the drainage duct to let thewater flow out. 4. When the container is full of water,put the drainage duct back again...

2 1 8. Clean the filter under the water tapand put it back in the pump intothe special guides. 9. Make sure that you tighten correct-ly the filter to prevent leakages. 11. Close the drain pump door. THE INLET HOSE FILTER ANDTHE VALVE FILTER It could be necessary to clean the filterswhen:• The applia...

45° 35° 6. Install again the inlet hose. Makesure that the couplings are tight toprevent leakages. 7. Open the water tap. EMERGENCY DRAIN Because of a malfunction, the appliancecannot drain the water.If this occurs, do steps (1) through (6) of'To clean the drain pump'.If necessary, clean the pump.Pu...

TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the prob-lem (refer to the table). If not, contactthe service centre. With some problems, the acousticsignals operate and the displayshows an alarm code: • - The appliance does not...

INSTALLATION UNPACKING 1. Use the gloves. Remove the exter-nal film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packagingmaterials. 4. Remove the internal film. 5. Open the door and remove all theitems from the drum. ENGLISH 29

6. Put the front piece on the floor be-hind the appliance. Carefully putdown the appliance with the rearside on it. Make sure not to dam-age the hoses. 1 2 7. Remove the polystyrene protectionfrom the bottom. 8. Pull up the appliance in vertical po-sition. 9. Remove the power supply cableand the dra...

12. Replace the plastic spacers withthe plastic caps. You can find thesecaps in the user manual bag. – We recommend that you keep the packaging and thetransit bolts for when youmove the appliance. – If the appliance is delivered in the winter months when thereare minus temperatures. Storeit at room ...

• The appliance must be level and sta- ble. CAUTION! Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the lev-el. THE INLET HOSE 35 O 35 O 35 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it i...

Water-stop device A The inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in the window «A» shows thisfault .If this occur, close the water tap andcontact the service centre to replacethe hose. WATER DRAINAGE There are differe...

Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drainhose in the spigot and tighten it witha clip. Make sure that the drain hosemakes a loop to prevent that remain-ing particles go in the appliance fromthe sink. • Directly to a built-in drain pipe in the room w...