Page 2 - Visit our website for:; Register your product for better service:; CUSTOMER CARE AND SERVICE; General information and tips
CONTENTS 1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. TECHNICAL INFORMATION ....
Page 4 - SAFETY INSTRUCTIONS; Installation
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard. • The operating water pressure (minimum and maxi- mum) must be between 0,5 bar (0,05 MPa) and 8 bar(0,8 MPa) • The ventilation openings in the base ...
Page 5 - TECHNICAL INFORMATION; Dimensions
mains plug, use a 13 amp ASTA (BS1362) fuse. • This appliance complies with theE.E.C. Directives. Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new sup-plied hose-sets. Old hose sets mustnot be reused. • Before yo...
Page 6 - PRODUCT DESCRIPTION
Level of protection against ingress of solid particlesand moisture ensured by the protective cover, ex-cept where the low voltage equipment has no pro-tection against moisture IPX4 Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton...
Page 7 - Accessories; Spanner; CONTROL PANEL; On Off button
4.1 Accessories 1 2 3 4 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear sideof the cabinet after the removal ofthe transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on theedge of a sink. 5. CONTROL P...
Page 8 - • After 5 minutes from the end of the; Programme knob; Turn this knob to set a programme.; Display; If the programme is completed but the symbol stays on:
• After 5 minutes from the end of the washing programme. Refer to 'At theend of programme'. 5.2 Programme knob 2 Turn this knob to set a programme. 5.3 Display 3 A B C The display shows: A • The programme time When the programme starts, the time decreases with steps of 1 mi-nute. • The delay start W...
Page 10 - PROGRAMMES
6. PROGRAMMES ProgrammeTemperature Type of loadmax. weight of load Cycledescription Functions Cottons 95° - Cold White and colouredcotton with normalsoil.max. 6 kg WashRinsesLong spin SPIN REDUC-TIONRINSE HOLDEXTRA RINSETIME SAVE 1) Cottons + Pre-wash 95° - Cold White and colouredcotton with heavyso...
Page 12 - CONSUMPTION VALUES
programmes in terms of combined energy and water consumption for washing normallysoiled cotton laundry.Set this programme to have a good washing results and decrease the energyconsumption. The time of the washing programme is extended. The washing temperature of the washing phase may differ from the...
Page 13 - BEFORE FIRST USE; Press button; Loading the laundry; Open the appliance door.
Pro- grammes Load (kg) Energy con- sump- tion (kWh) Water con- sump- tion (li- tre) Ap- proxi- mate pro- gramme dura- tion (mi- nutes) Re- main- ing mois- ture (%) 1) L 60260 FL Re- main- ing mois- ture (%) 1) L 60460 FL Re- main- ing mois- ture (%) 1) L 60660 FL Standard 40°C cotton 3 0.51 38 158 5...
Page 14 - Filling the detergent and additives; This is the maximum level for the quantity of liquid additives.
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain ...
Page 15 - Check the position of the flap; – Do not use gelatinous or thick; Setting and starting a; Turn the programme knob.
Check the position of the flap 1. Pull out the detergent dispenser un-til it stops. 2. Press the lever down to remove thedispenser. 3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn theflap down. With the flap in the positionDOWN: – Do not use gelatinous or thick liquid d...
Page 17 - HINTS AND TIPS; The laundry load
• The door lock symbol goes off.• Press button 1 to deactivate the ap- pliance. After five minutes from theend of the programme, the energysaving function automatically deacti-vates the appliance. When you activate the applianceagain, the display show the endof the last set programme. Turnthe progra...
Page 18 - Water hardness; soft; CARE AND CLEANING; Descaling
• Do not mix different types of deter- gents. • To help the environment, do not use more than the correct quantity of de-tergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the pro-gramme temperature ...
Page 19 - To clean the dispenser:
• Set the hottest cotton wash pro- gramme • Use a correct quantity of powder de- tergent with biological properties. After each wash, keep the door open fora while to prevent mould and to let un-pleasant smells go out. 11.4 Door seal Regularly examine the seal and removeall objects from the inner pa...
Page 20 - Put back the dispenser in the recess.; Drain pump; • The display shows an alarm code be-; To clean the drain pump:; Open the drain pump door.
5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the recess. 11.7 Drain pump Regularly examine the drainpump and make sure that it isclean. Clean the pump if:• The appliance does not drain the wa- ter. • The drum cannot turn.• The appliance makes an unusual noise because of th...
Page 21 - Close the drain pump door.; The inlet hose filter and; • The indicator of button
6. Remove fluff and objects from thepump. 7. Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre. 2 1 8. Clean the filter under the water tapand put it back in the pump into thespecial guides. 9. Make sure that you tighten correctlythe filter to preve...
Page 22 - To clean the water inlet filters:; Emergency drain; Remove the water inlet hose
To clean the water inlet filters: 1. Close the water tap. 2. Remove the water inlet hose fromthe water tap. 3. Clean the filter in the inlet hose witha stiff brush. 4. Remove the inlet hose behind theappliance. 5. Clean the filter in the valve with astiff brush or a towel. 45° 20° 6. Install again t...
Page 23 - TROUBLESHOOTING; - The appliance does not fill with; Problem; The water tap is closed.
12. TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.First try to find a solution to the problem(refer to the table). If not, contact theservice centre. With some problems, the acousticsignals operate and the display showsan alarm code: • - The appliance does n...
Page 25 - Too much laundry load.; INSTALLATION; Fixing plate kit; Available from your authorized dealer.; Unpacking; Remove the cardboard top.
Problem Possible cause Possible solution You did not remove thestubborn stains beforeyou wash the laundry. Use special products to removethe stubborn stains. Incorrect temperaturewas set. Make sure that you set the cor-rect temperature. Too much laundry load. Decrease the laundry load. After the che...
Page 26 - Remove the internal film.
4. Remove the internal film. 5. Open the door and remove all theitems from the drum. 6. Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure not to damage the ho-ses. 1 2 7. Remove the polystyrene protecti...
Page 28 - Positioning and levelling
13.3 Positioning and levelling x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment o...
Page 29 - The inlet hose; • Connect the hose to the appliance.; Water pressure
13.4 The inlet hose 20 O 20 O 20 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rect position. • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaksfrom th...
Page 30 - Water drainage; With the plastic hose guide.
Water-stop device A The inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in the window «A» shows thisfault .If this occur, close the water tap andcontact the service centre to replace thehose. 13.5 Water drainage There are di...
Page 31 - • If the end of the drain hose is this (see; Without the plastic hose guide.; • Directly to a built-in drain pipe in the
• If the end of the drain hose is this (see the drawing), you can push it directlyinto the stand pipe. Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drainhose in the spigot and tighten it with aclip. Make sure that the drain hosemakes a loop to prevent that r...
Page 32 - In the interest of the environment; • Connect the appliance to the FOUL; ENVIRONMENT CONCERNS
13.6 In the interest of the environment • Connect the appliance to the FOUL system for the drain water. The sew-age works keeps the drain water forthe treatment before to release safelyit into a river. Do not connect this ap-pliance to the surface drain system ofthe water because it releases the dra...
