AEG 69802G-M- Manuals

6 HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner. Upon, ignition, keep the knob pushed down about 5 seconds, then adjust the flame as required.If the burner does not ignite, turn the control knob to zero, an...

7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. Pan Supports To keep the pan supports in the correct position, they ar...

8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM „ There is no spark when lighting the gas „ The gas ring burns unevenly SOLUTION ‹ Check that the unit is plugged in and the electrical s...

10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereofis proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair orreplace the same FREE O...

11 Burner Dia. Tap By-pass 1/100 mm Auxiliary 28 Semi-rapid 32 Rapid 40 Aeration adjustment none OVERALL DIMENSIONS Width: 580 mm. Depth: 510 mm. Height: 88 mm. Weight: 8 Kg. CUT OUT DIMENSIONS Width: 550 mm. Depth: 470 mm. Thickness: 30 mm. SUPPLY CONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear r...

12 BURNER RAPID SEMI-RAPID AUXILIARY (large) (medium) (small) POSITION MAX MIN MAX MIN MAX MIN NOMINAL THERMAL POWER kW 2.9 0.65 1.9 0.45 1.0 0.33 NOMINAL FLOW RATE m 3 /h 0.276 0.062 0.181 0.043 0.095 0.031 NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 1/100 mm NOMINAL THERMAL POWER kW 2.7 0.6...

13 Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards.Any gas installation must be carried out by a registered CORGI installer. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions in...

14 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. It is import...

15 550 470 580 510 Cut Out Size The dimensions of the cut-out are given in the diagram. Building InBuilding over a cupboard ordrawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surf...

17 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.Th...

18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity supply (mains), with a minimum gap of 3mm. between the switch contacts and of a type suitable for the required load incompliance with the current el...

19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...

21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...

22 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite.2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...

23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors arefitted and the gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF...