AEG 11191 - Manuals

5 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR DATA FOR PRODUCT SELECTION LOW VOLTAGE CIRCUITControl circuit Nominal supply voltage U n (7) [V DC ] 24, 48, 60, 64, 110, 125, 200, 220 Range of voltage [0.7 - 1.25] U n [0.8 - 1.1] U n Maximum closing power (7) (8) [...

6 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR DIRECT OVERCURRENT RELEASE SELECTION AVAILABLE TRIPPING DEVICES AVAILABLE TRIPPING DEVICES UR26/40/46 UR60/80 Available setting ranges (in kA) with their corresponding codification UR26 UR40 UR46 UR60 UR80 type Design...

7 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR INFORMATION FOR PRODUCT INTEGRATION MAIN DIMENSIONS FOR UR26/40/46 Dimensions without tolerances are indicative. All dimensions are in mm. The maximum allowed flatness deviation of the support frame is 0.5 mm. (1) Arc...

8 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR MAIN DIMENSIONS FOR UR60/80 Weights (1) [kg] ± 5% UR26 UR40 UR46 UR60 UR80 With arc chute 81 77 98 110 139 150 With arc chute 82 87 108 120 149 160 With arc chute 64 133 154 INSULATION DISTANCES FOR UR26/40/46/60/80 W...

9 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR ARC CHUTE INSTALLATION ARC CHUTE 81 AND 82 Designation code for order form (arc chute 64 installation) Arc chute type Circuit breaker Arc chute installation Codification standard option 64 UR26/40 SE 2 S-CC 5 S-OC 6 O...

10 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR Coil characteristics Closing pulse 0.5 to 1s holding E-type opening pulse M-type 0,5 to 1s U n I nom I min E I min M I max R1 I nom I min I max Rs Rp I nom I min I max [V DC ] [A] [A] [A] [A] [ Ω ] [A] [A] [A] [ Ω ] ...

11 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR Coil characteristics Closing pulse 0.5 to 1s holding E-type opening pulse M-type 0,5 to 1s U n I nom I min E I min M I max R1 I nom I min I max Rs Rp I nom I min I max [V DC ] [A] [A] [A] [A] [ Ω ] [A] [A] [A] [ Ω ] ...

12 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR OPTIONS (SUBJECT TO ADDITIONAL COSTS) MOBILE CONNECTOR - UR26/40/46/60/80 Auxiliary switches Control voltage Fixed connector type Mobile connector (without cable) Number of pin (delivered with connector) Cable gland ...

13 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR BIM INDIRECT RELEASE (SHUNT TRIP) WITH INTEGRATED MANUAL RELEASE POSITION INDICATOR - UR26/40/46/60/80 LOW VOLTAGE WIRING DIAGRAM HARTING CONNECTOR TECHNICAL DATA Note: Certain option combination might not be compati...

14 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR BIM5 & BIM6 - UR26/40/46 UR26/40/46 BIM7 & BIM8 - UR60/80 UR60/80 The terminal block allows the connection between 2.5 mm² cables from the BIM5 and 2.5 mm² cables from the battery and 6 mm² cables from the CI...

15 HIGH-SPEED DC CIRCUIT-BREAKERS FOR FIXED INSTALLATIONS, EN/IEC STANDARD, TYPE UR The manual closing device, mainly used for maintenance operations, enables to close and open the circuit breaker without low voltage supply and under no load. Installed on the rear side of the circuit breaker closing...

Copyright© • 2023 • Sécheron SA This document is not contractual and contains information corresponding to the level of technology at the date of printing. Sécheron reserves the right to modify and/or improve the product, whose characteristics are described in these documents, as required by new tec...

14. This pump controller has a full pump speed voltage threshold of approximately 3.7VDC, where the full pump speed will be achieved with signal input voltage at or above 3.7VDC and above which no further change in pump speed will occur. This ensures that when a TPS signal is used to drive pump spee...

MODE 4 – Switched Speed On - Demand from Low to High Mode 4 can be activated by any relay or switch providing 5VDC or higher to the control wire. A relay for this purpose could be activated using the programmable output from a tunable ECU, or via a boost or WOT switch connected to 12VDC to name a fe...

Fuel System Troubleshooting Pump does not run at all. Do you have voltage at the pump terminals? Is the “+”terminal connected to +12 V and the “-“ terminal connected to the battery ground cable? Is the fuel line going to the engine compartment connected to the same side of the fuel pump as the power...

Aeromotive, Inc. Technical Bulletin #101 From: Aeromotive Technical Department Date: 10/10/2011 Re: Fuel Filtration: Selecting the correct filter to prevent lean-out and pump failure. STOP!! If you are selling or installing a fuel filter on the inlet of an Aeromotive fuel pump, be certain you do not...

the fuel and turning it from liquid into vapor. Bottom line: Inlet restrictions create vacuum, which causes cavitation, which in turn causes vapor-lock and fuel pump damage. Of course, drivability problems and even engine damage can result! Lesson: Don’t combine high flow, efficient fuel pumps with ...

Above are various versions of “100-micron” fuel filters/elements. Note: the top element is the Aeromotive 100- micron element P/N #12604, as found the fuel filter assembly P/N #12304. Note the various filters all have “billet” housing, with AN connections, and can be disassembled for inspection and ...

Contact US RGA NUMBER REQUIRED FOR ALL RETURNS TO AEROMOTIVE. To obtain an RGA number, please call (913) 647–7300 and ask for the Returns and Repairs department. • Shipping Address Aeromotive Inc. 7805 Barton St. Lenexa, KS 66214 • Sales & Returns Aeromotive Inc. 11414 W 79th Street. Lenexa, KS ...

WARNING: This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit: www.p65W arnings.ca.gov Aeromotive, Inc. 7805 Barton Street, Lenexa, KS 66214 Phone: (913) 647-73...