AEG 11191 - Manual
AEG 11191 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – To use this pump in your vehicle’s fuel system,; you must do the following; continuous; The following steps are typical of most installations:
- Page 3 – swivel fitting to make the connection to the pump.; Make sure you use
- Page 4 – . A PWM signal can only be used if
- Page 5 – CONTROL CONFIGURATIONS:
- Page 6 – Switch
- Page 8 – Fuel System Troubleshooting; Pump does not run at all.; Pump performs poorly or runs intermittently
- Page 9 – can create both high outlet pressure
- Page 10 – worth a thousand words...”
- Page 11 – are sold and recommended as appropriate pre-filters.; However, excepting the
- Page 12 – Contact US; RGA NUMBER REQUIRED FOR ALL RETURNS TO AEROMOTIVE.; Shipping Address
- Page 13 – This product can expose you to chemicals,
AEROMOTIVE
Part # 11191/11192/11195/11196
Product Description
INSTALLATION INSTRUCTIONS
This product is not legal for sale or use on emission-controlled vehicles except when used as a direct
replacement part matching OEM specification.
WARNING!
Always be aware of flammable situations. Drilling and grinding can be
potential ignition sources. Extinguish all open flames, prohibit smoking and
eliminate all sources of ignition in the area of the vehicle and workspace before
proceeding with the installation. Ensure you are working in a well ventilated area
with an approved fire extinguisher nearby.
WARNING!
Installation of this product requires modification to a fuel tank/ the fuel
system, failure to satisfy all safety considerations will result in fire, explosion,
injury and/or loss of life to yourself and/or others. All fuel system components
MUST be located as far from heat sources as possible, like exhaust, engine block,
etc.
WARNING!
Mechanical and hydraulic lifting devices can tip over or lower accidentally
due to incorrect maneuvering or technical errors. A falling object can cause
injury and/or loss of life to yourself and/or others. When working under the
vehicle, always use stands, and ensure that the ground or floor is stable and
level. Never crawl under a vehicle which is only supported by a jack.
WARNING!
The fuel system is under pressure. Do not open the fuel system until the
pressure has been relieved. Refer to the appropriate vehicle service manual for
the procedure and precautions for relieving the fuel system pressure
.
CAUTION!
When installing this product always wear safety glasses and other
appropriate safety appeal. A drilling operation will cause flying metal chips. Flying
metal chips can cause eye injury.
CAUTION:
Installation of this product requires detailed knowledge of automotive systems
and repair procedures. We recommend that this installation be carried out by a
qualified automotive technician. Careless installation of this product can result in
damage to the product, injury or loss of life to yourself and/or others.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for AEG 11191
Summary
Compatible Fuels: Pump Gas Race Gas E85 Alcohol/Ethanol To use this pump in your vehicle’s fuel system, you must do the following : • Utilize a by-pass style fuel pressure regulator in the system. • Utilize AN-12 size high pressure fuel lines, fittings and o-rings for all connections from the fuel t...
using an Aeromotive fuel filter, you can attach the filter directly to the fuel pump utilizing an AN-12 fitting (Aeromotive P/N 15612) and 2 sealing o-rings (AN-12 o-ring pack Aeromotive P/N 15624). Note: It is recommended that a fuel shut off valve be installed between the fuel tank outlet and the ...
Note: Be sure to route all electrical wires clear of any moving suspension or drivetrain components and any exhaust components! Protect wires from abrasion and road obstructions or debris. 9. Make sure you use stranded, insulated copper wire, in the sizes shown, with matching crimp-type connectors f...
