AEG 11189 - Manuals

5 Control de riesgos al usar herramientas neumáticas • El aire comprimido que utilizan los equipos neumáticos puede resultar peligroso. Objetos como abrazaderas, rebabas, astillas, polvo y otros residuos pueden ser impulsados por el flujo de aire a gran velocidad a la cabeza o a los ojos. El flujo d...

Palanca de gatillo Entrada de aire Entrada para la tuerca o birlo Entrada para el retenedor de cuadro Selector de dirección de giro Dado de impacto Impulsor de cuadro Instalación del dado • Desconecte la herramienta de la toma de aire antes cambiar de dado. • Seleccione el dado que necesita y colóqu...

8 Puesta en marcha Encendido • Encienda el compresor de aire y permita que se llene. • Regule la presión de salida del compresor de aire a 621 kPa (90 PSI). La herramienta opera a este nivel de presión, de operarse a niveles mayores, la vida útil de la herramienta será menor. • Deje correr un poco d...

9 Mantenimiento • Las herramientas neumáticas requieren lubricación constante a lo largo de su vida útil y durante su operación. El aire comprimido que necesita la herramienta para funcionar contiene humedad que puede oxidar el motor y los baleros de la herramienta. Para evitar esta posibilidad es n...

Centros de Servicio Autorizados 11 En caso de tener algún problema para contactar un Centro de Servicio consulte nuestra página www.truper.com donde obtendrá un listado actualizado, o llame al teléfono: (800) 690-6990 ó (800) 018-7873 donde le informarán cuál es el Centro de Servicio Autorizado más ...

ESPAÑOL www.truper.com 06-2019 Sello del establecimiento comercial: Fecha de entrega: Modelo Código Marca TPN-886H-2 11189 Póliza de Garantía Este producto, sus piezas y componentes están garantizados por 2 años contra defectos de fabricación, funcionamiento y mano de obra, excepto cuando: el produc...

Manual TPN-886H-2 Model Code TPN-886H-2 Applies for: 11189 1/2” Use oil continuously and dosed to lubricate the tool. WARNING CAUTION Read this manual thoroughly before using the tool. EN GL ISH ES PAÑOL Air Impact Ratchet

2 TPN-886H-2 ENGLISH Contents CAUTION Keep this manual for future references. The illustrations in this manual are for reference only. They might be different from the real tool. To gain the best performance of the tool, prolong the duty life, make the Warranty valid if necessary, and to avoid hazar...

3 TPN-886H-2 11189 1/2” 3 CFM 90 PSI 150 RPM Rocking Dog 68 Nm (50 lb-ft) 2,5 lb 3/8” 1/4 NPT Head on ENGLISH CAUTION Technical Data Dust, water and lack of oil specific for pneumatic tools are the main cause of potential malfunction of the tool. Setting up a Brand UNI-LL-1/4 centralized filter-oile...

4 ENGLISH General Safety Warnings for Pneumatic Tools Keep your work area clean, tidy and well lit. Cluttered and dark areas may cause accidents. Never use the tool in explosive areas or in the presence of flammable liquids or with no ventilation. Sparks the tool generates could trigger anexplosion ...

5 ENGLISH Risk Control When Using Pneumatic Tools • Compressed air out of pneumatic equipment may be dangerous. Objects like brackets, burrs, splinters, dust and other residues may be impelled towards head and eyes due to high speed of the air flow. The air flow itself can only injure soft tissue su...

7 ENGLISH Parts Assembly Trigger Lever Air Intake Nut or lug input Square Retainer Input Turn Direction Selector Impac Die Square Impeller Die Set Up • Disconnect the tool from the air intake before replacing dies. • Select the die needed and set it in the square impeller. • Use always impact dies f...

8 A C F G D B ENGLISH Start Up Turning ON • Turn on the air compressor until is full. • Regulate output pressure of the air compressor to 90 PSI The tool operates at this pressure level. if operated at higher levels, the useful life of the tool will decrease. • Allow some air to flow through the hos...

9 • Pneumatic tools need to constantly be lubricated during its useful life and while operating. Compressed air needed in tool to run contain humidity which can rust the motor and bearings. To prevent this possibility, is necessary to constantly administer through a brand UNI-LL-1/4 Centralized Filt...

11 ENGLISH AGUASCALIENTES BAJA CALIFORNIA BAJA CALIFORNIA SUR CAMPECHE CHIAPAS CHIHUAHUA MEXICO CITY COAHUILA COLIMA DURANGO ESTADO DE MÉXICO GUANAJUATO GUERRERO HIDALGO JALISCO MICHOACÁN MORELOS NAYARIT DE TODO PARA LA CONSTRUCCIÓN GRAL. BARRAGÁN #1201, COL. GREMIAL, C.P. 20030, AGUASCALIENTES, AGS...

www.truper.com 06-2019 TPN-886H-2 11189 12 ENGLISH Model Code Brand 2 YEARS Warranty policy Delivery date: This product, its parts and components have a 2 year warranty against defects in its manufacture, operation and workmanship, except when: the product has been used in conditions other than thos...

This ensures allowance for minimum, closed throttle TPS settings of up to 0.5VDC are allowed and will not affect fuel pump speed at idle. 14. This pump controller has a full pump speed voltage threshold of approximately 3.7VDC, where the full pump speed will be achieved with signal input voltage at ...

Fuel System Troubleshooting Pump does not run at all. Do you have voltage at the pump terminals? Is the “+”terminal connected to +12 V and the “-“ terminal connected to the battery ground cable? Is the fuel line going to the engine compartment connected to the same side of the fuel pump as the power...

Aeromotive, Inc. Technical Bulletin #101 From: Aeromotive Technical Department Date: 10/10/2011 Re: Fuel Filtration: Selecting the correct filter to prevent lean-out and pump failure. STOP!! If you are selling or installing a fuel filter on the inlet of an Aeromotive fuel pump, be certain you do not...

the fuel and turning it from liquid into vapor. Bottom line: Inlet restrictions create vacuum, which causes cavitation, which in turn causes vapor-lock and fuel pump damage. Of course, drivability problems and even engine damage can result! Lesson: Don’t combine high flow, efficient fuel pumps with ...

Above are various versions of “100-micron” fuel filters/elements. Note: the top element is the Aeromotive 100- micron element P/N #12604, as found the fuel filter assembly P/N #12304. Note the various filters all have “billet” housing, with AN connections, and can be disassembled for inspection and ...

Contact US RGA NUMBER REQUIRED FOR ALL RETURNS TO AEROMOTIVE. To obtain an RGA number, please call (913) 647–7300 and ask for the Returns and Repairs department. • Shipping & Returns Aeromotive Inc. 10955 Mill Creek Road Lenexa, KS 66219 General Inquiries and Tech Line: (913) 647-7300 General Em...

WARNING : This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit: www.p65Warnings.ca.gov AEROMOTIVE, INC. LIMITED WARRANTY This Aeromotive Product, with proof of ...