ADTRAN Protection Switch - Manuals

Page 2 - Rackmount the Units; Figure 1. TRACER MPS System Rackmount Configuration; TRACER MPS

2 1 Rackmount the Units Install the TRACER MPS system in a location that requires minimal antenna feedline length (the loss in this cable directly affectsoverall system performance). The TRACER MPS should be mounted in a rack between the two BBP components of the TRACER systems (see Figure 1 on page...

Page 3 - Creating the VT100 Chain; STANDBY UNIT VT100 Connection; Connecting to the Unit; Configure the COM port with the following parameters:

3 2 Creating the VT100 Chain A single VT100 connection through the TRACER MPS provides access to both the primary (MAIN) and SECONDARY TRACER units. Follow the steps below to create the VT100 chain. 1. Connect the RS-232 port (DB-25) on the rear panel of the MAIN TRACER BBP to the TRACER MPS VT100 i...

Page 4 - Reviewing the Menus; Navigational Help; ISABLED; . To disable the modem

4 2 8 10 4 5 6 9 1 7 4 Reviewing the Menus The TRACER MPS software interface consists of a single menu screen (shown below). Navigate through the available menu options using the up and down arrow keys. Alternately, the numbered menu options may be selected by entering the appropriate menu number di...

Page 5 - Connecting the T1 Interfaces; MAIN UNIT T1B Interface

5 MANAGEMENT T R A C E R MAIN STANDBY OUT NO COM NC MN COM SB IN ALARMS DC POWER RF ANTENNA TO DTE RS-232 MONITOR T1B T1A MAIN TRACER STANDBY TRACER MONITOR POWER MODULE USE COPPER CONDUCTORS ONLY MAIN OUT IN IN OUT B A B A STAND BY T1B T1A TRACER MPST1A/T1B Interfaces TRACER MPSMAIN T1A Interface 6...

Page 6 - TRACER MPS Antenna Interface; Connecting the Antenna Interfaces (TRACER BBP and RFC Systems); Repeat Step 2 for the STANDBY TRACER BBP and RFC.

6 MANAGEMENT T1B T1A IF ANTENNA T R A C E R MAIN STANDBY OUT NO COM NC MN COM SB IN ALARMS DC POWER RF ANTENNA TO DTE RS-232 MONITOR T1B T1A MAIN TRACER STANDBY TRACER MONITOR POWER MODULE USE COPPER CONDUCTORS ONLY OUT IN IN OUT B A B A MAIN STAND BY 2 5 6 TRACER MPS Antenna Interface TRACER MPS ST...

Page 7 - Connecting the Antenna Interfaces (TRACER 4103 and 4203 Systems); MAIN UNIT Antenna Interface

7 6b Connecting the Antenna Interfaces (TRACER 4103 and 4203 Systems) 1. Connect the Antenna interface (N-Type connector) of the MAIN TRACER 4103/4203 (labeled 1 below) to the MAIN RF interface (SMA connector) of the TRACER MPS (labeled 2 below) using a male N-Type to male SMA cable. 2. Repeat Step ...

Page 8 - Connecting the Alarm Contacts; NO Alarm Contact

8 7 Connecting the Alarm Contacts 1. Connect the NO (Normally Open) alarm contact of the MAIN TRACER BBP (labeled 1 below) to the MN alarm contact in the IN alarm block of the TRACER MPS (labeled 2 below). The TRACER BBP provides two sets of alarm contacts; for normal configuration, use the NO locat...

Page 9 - NTERFACES

9 8 Supplying Power to the Unit The TRACER MPS can operate from a supply between 21 and 63 Volts DC, with either polarity referenced to ground, and consumes 3 Watts nominal, 20 Watts peak (during relay switching). Current required (in Amps) is determined by dividing the power consumed (in Watts) by ...