AcuRite 615 - Manuals - manualsarea.com

Page 2 - Unpacking Instructions; product. Locate the tab and peel off to remove.; Package Contents; Sensor mounting bracket; PRODUCT REGISTRATION; Register online; AcuRite; IMPORTANT

2 Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference. Unpacking Instructions Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab ...

Page 3 - Mounting Hardware

3 Features & Benefits 3-in-1 SENSOR 1. Temperature & Humidity Sensors (internal) 2. Release Lever for Battery Access3. Mounting Point4. Wind Speed Anemometer 5. Mounting Hardware Includes anchors and screws. 6. Mounting Bracket7. A-B-C Switch (not shown) ID code that must match display’s A-B...

Page 6 - SETUP; Install or Replace Batteries; A B C

6 SETUP Set the A-B-C Switch The A-B-C switch is located inside the battery compartment. It can be set to A, B or C. However, you must select the same letter choices for both the sensor and the display unit in order for the units to synchronize. Install or Replace Batteries AcuRite recommends high q...

Page 7 - Display Unit Setup

7 PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS. BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be used for an ...

Page 8 - Measurement

8 Atomic Clock AcuRite atomic clocks use a radio-controlled signal to synchronize to the correct time broadcast by the National Institute of Standards and Technology (NIST) Radio Station WWVB, located near Fort Collins, Colorado. WWVB broadcasts the current time and date with split-second accuracy.T...

Page 9 - Visit us online to view installation photos and; View Video

9 Placement for Maximum Accuracy AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display unit and the sensor are critical to the accuracy and performance of this product. Display Unit Placement Place the display unit in a dry area free of dirt and ...

Page 10 - Basic Setup is Complete; Top Mount; Do not install during

10 3-in-1 Sensor Installation Guidelines INSTALLATION HEIGHT Mount the sensor at least 5 feet (1.5 meters) off the ground (higher is better for wind measurement) in an open area. Secure to fence post, 2’x4’ wood, 3/4” pole, etc. (not included) LEVEL INSTALLATION Use a bubble level (not included) to ...

Page 11 - ready for superior weather prediction.; Weather Forecast; personalized for your exact location.; Multi-Variable History Chart; pressure, temperature and wind speed readings.; Wind Speed; the change in AVERAGE hourly wind speed.; Barometric Pressure; OPERATION

11 Using The Weather CenterLearning Mode Self-Calibrating Forecasting use a unique algorithm to analyze changes in pressure over a time period (called Learning Mode) to determine your altitude. After 14 days, the Learning Mode icon disappears from the display screen. At this point, the self-calibrat...

Page 12 - Weather Ticker; when applicable

12 High & Low Records The “MIN/MAX” button displays minimum and maximum recordings for outdoor and indoor temperature and humidity. To view the MINIMUM temperature and humidity readings, press and release the “MIN/MAX” button until the “MIN” icon appears on the display next to the low records. T...

Page 13 - Customize Weather Ticker Messages; during manual review. The “ ” and “ ” buttons do not add or remove

13 Customize Weather Ticker Messages Customize which messages you want to scroll across the WEATHER TICKER:1. Press the “ ” button to manually cycle through each message available.2. During the manual review: PRESS the “ ” button to activate the current scrolling message. The corresponding “ ” appea...

Page 14 - Troubleshooting

14 Troubleshooting Problem Possible Solution No outdoor sensor reception no bars • Relocate the display unit and/or the 3-in-1 sensor. The units must be within 330 ft (100 m) of each other. • Make sure both units are placed at least 3 feet (.9 m) away from electronics that may interfere with the wir...

Page 15 - If your AcuRite product does not operate properly after trying

15 If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call (877) 221-1252 for assistance. Problem Possible Solution Inaccurate wind readings • What is wind reading being compared to? Pro weather stations are typically mounted at 30 ft h...

Page 16 - Display Unit Care; Clean the Sensor; Snow & Freezing Weather; Clean the Wind Anemometer

16 FCC Information This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:1- This device may NOT cause harmful interference, and2- This device must accept any interference received, including interference that may cause undesired operation.This equipment...

Page 17 - Limited One Year Warranty; Customer Support

17 At AcuRite, we proudly uphold our commitment to quality technology. Chaney Instrument Co. warrants that all products it manufactures to be of good material and workmanship, and to be free of defects when properly installed and operated for a period of one year from the date of purchase. We recomm...

Page 18 - It’s more than accurate, it’s; designed to provide you with information you can depend on to

©2012 Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. Patent numbers: 5,978,738; 6,076,044; 6,597,990; US 7,637,141 B2. Printed in China ...