Page 3 - iii; Special notes on LCD monitors; Safety instructions; Cleaning your monitor; Connecting/disconnecting the device
iii Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. • You may f...
Page 4 - iv; Accessibility; Warnings; Using electrical power
iv Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect yo...
Page 5 - Product servicing
v ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in ...
Page 6 - Potentially explosive environments; Additional safety information
vi Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition. Potentially explosive environments Switch o...
Page 7 - vii; Disposal instructions
vii Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit LCD pixel ...
Page 8 - viii; Tips and information for comfortable use; Finding your comfort zone
viii This product has been shipped enabled for power management: • Activate display’s Sleep mode within 15 minutes of user inactivity. • Activate computer’s Sleep mode within 30 minutes of user inactivity. • Wake the computer from Sleep mode by pushing the power button. Tips and information for comf...
Page 9 - ix; Taking care of your vision
ix Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The following sections provide suggestions on how to reduce eyestrain.Eyes • R...
Page 10 - TABLE OF CONTENTS
TABLE OF CONTENTS UNPACKING............................................................................................ 1ATTACHING / REMOVING THE BASE .................................................... 2SCREEN POSITION ADJUSTMENT ......................................................... 3CONNECTIN...
Page 11 - UNPACKING; LCD Monitor
EN-1 UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. LCD Monitor Quick Start Guide AC Power Cord HDMI Cable (Optional) DP Cable (Optional) USB Cable (Optional)...
Page 12 - ATTACHING / REMOVING THE BASE
EN-2 ATTACHING / REMOVING THE BASE Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. 1.Attach the monitor stand arm to the base. 2.Ensure that the base is screwed tight onto the monit...
Page 13 - SCREEN POSITION ADJUSTMENT; • Height
EN-3 SCREEN POSITION ADJUSTMENT In order to optimize the best viewing position, you can adjust the height/tilt of the monitor.• TiltPlease see the illustration below for an example of the tilt range.Only at the highest point can 25 degrees of recline be offered for the angle of elevation. • Height A...
Page 14 - Do not expose the monitor to rain, excessive moisture, or dust.; CLEANING YOUR MONITOR
EN-4 CONNECTING THE POWER CORD Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. Plug one end of th...
Page 15 - State LED
EN-5 POWER SAVING The monitor will be driven into “Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time f...
Page 16 - CONNECTOR PIN ASSIGNMENT
EN-6 CONNECTOR PIN ASSIGNMENT 19-Pin Color Display Signal Cable* * only for certain models 20-Pin Color Display Signal Cable* * only for certain models PIN Meaning PIN Meaning 1. TMDS Data2+ 10. TMDS Clock+ 2. TMDS Data2 Shield 11. TMDS Clock Shield 3. TMDS Data2- 12. TMDS Clock- 4. TMDS Data1+ 13. ...
Page 17 - Standard Timing Table; Mode
EN-7 Standard Timing Table * Only for DP mode, not for HDMI mode. Mode Resolution Remark 1 640 x 480 60 Hz 2 720 x 480 60 Hz 3 1280 x 720 60 Hz 4 720 x 576 50 Hz 5 1280 x 720 50 Hz 6 1920 x 1080 50 Hz 7 1920 x 1080 60 Hz 8 800 x 600 60 Hz 9 1024 x 768 60 Hz 10 3840 x 2160 24 Hz 11 3840 x 2160* 60 Hz...
Page 18 - INSTALLATION
EN-8 INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps1. 1-1 Connect HDMI Cable (Only HDMI-input model) a. Make sure both the monitor and computer are powered-OFF.b. Connect the HDMI cable to the computer.When using HDMI, you can press any button,...
Page 19 - USER CONTROLS; Base Controls; Input
EN-9 USER CONTROLS Base Controls Icon Item Description Power button/ indicator Turns the monitor on/off. Blue indicates power on. Amber indicates standby/power saving mode. OSD functions Press to view the OSD. Press again to enter a selection in the OSD. Input Input button Press to toggle input sour...
Page 20 - Adjusting the OSD settings; OD
EN-10 Adjusting the OSD settings The OSD (on-screen display) can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following page: Ma...
Page 22 - The Function page
EN-12 The Function page Open the Function page to select Picture, Color, OSD or Setting functions, and adjust the settings which you want using the arrows. You can also view your monitor’s system information from this page. When you are done, use to go back one level. Adjusting the Picture 1. Press ...
Page 28 - TROUBLESHOOTING
EN-18 TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the trouble-shooting list below to see if you can self-diagnose the problem. (HDMI/DP Mode) Problems Current Status Remedy No Picture LED ON Using OSD, adjust brightness and contrast to maximum or reset to their defa...
Page 30 - Federal Communications Commission
EN-20 Acer America Corporation 333 West San Carlos St., Suite 1500 San Jose, CA 95110 U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two ...
Page 31 - minute of inactivity respectively.
EN-21 ENERGY STAR ® Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps protect the environment without sacrificing features or performance. Acer is proud to offer our customers products with the ENERGY STAR mark. What is ENERGY STAR? Products that are ENERGY STAR...
