Acer Smart Touch Kit (INTPJ-STK1)- Manuals

5 Hardware Installation Connection Topological graph: Installation requirements 1. The display surface for installation should be flat. For a better touch performance, the flatter the surface is, the easier the adjustment will be. 2. Take care of interference from sunlight when install it. We recomm...

6 Installation Step 1: Emitter Put an adhesive tape on the back side of the emitter, attach emitter 3cm above top center of the projection screen, and secure the emitter by 4 screws (as shown in Pic). Note: if it’s a Dual-Screen Smart Touch Kit, one emitter should be installed 3cm above the top of p...

8 First, fix the sensor to the black supporting bracket with the matched screw by screwdriver, as following: At last, fix the supporting bracket to the projector with matched small screws, as following: Step 3:Cable connection: Connect the sensor with computer by using the USB cable. Emitter is conn...

10 Step 4:After installation, the shortcut icon will be added to desktop. After the installation of education software, the shortcut icon as picture will be added to desktop: Software Uninstall Uninstall software: Open the computer control panel, and click the “software and function” to choose and u...

11 Note: If it is a Dual-Screen Smart Touch Kit, Left camera should show the image of left projection screen, and right camera should show the right projection screen.When it is in camera mode, the image is in the opposite way as shown in Pic 4: Pic 4 Then please right click on the image, chose “exc...

13 Calibration Software Introduction Start IWB calibration software, click “operation” menu Run: Run the calibration program to start the sensor icon. Stop: Close the sensor icon, then no more touch functions. Parameter Setting: Software parameters Setting Auto Mask Clutter: Auto shield the interfer...

14 Parameter setting Image Sensor Settings （ 1 ） Normal Use Setting Set the Proportion of the spot (20%-80%): refers to the sensitivity of mouse reaction to lightspot sizes, the larger the value is, the worse the sensitivity becomes. The Brightness coefficient (0-255): refers to the sensitivity of s...

15 Double Screen: two Smart Touch Kits work with two projectors to become a big touch screen. Finish installation and connection, then the program will be in double screen mode automatically. Parameter Settings:Gesture settings (1) Windows Gesture Settings Start All Windows Gesture: refers to the sw...

17 Auto Mask Clutter (Ctrl+Shift+A) Auto mask clutter is the first step to do before performing manual calibration. Please select “Auto Mask Clutter” from “Mask Bitmap Edit” or press “Ctrl+Shift+A”. The program will specify the active area automatically. Manual Calibration After auto mask clutter, c...

19 Installation and debugging Click “installation and debugging” menu （ 1 ） Tuning Webcam Image Mode: The projection image which catched by camera will be showing in software interface. Adjust the projection image into the red frame according to the camera debuggingrequirement. （ 2 ） Tuning Laser Tr...

20 （ 3 ） Normal Usage Image Mode: after the calibration, all operations can be done by the finger instead of the mouse. （ 4 ） Mouse: click mouse, then you can only do single touche in Windows. （ 5 ） Touch Pad: click touch pad, then you can do multi-touches in Windows. （ 6 ） Touch Pad Aspect Ratio: T...

21 Gesture recognition Introduction Mouse operations Single Click: single finger tap Double Click: single finger tap twice quickly at the same position. Right Click: single finger stays for 2 or 3 seconds at the same position for right click function. Scroll Bar: open a website, scroll the page up a...

22 Application Software Introduction of the main toolbar When you use GLBoard for the first time, double click GLBoard to start the program, the interface includes three areas, shown as the following: Function of each button on the tool bar Icon Name Function Start menu Open the menu list Resource L...

28 Troubleshooting 1. Open the program and an error is shown as “No valid USB Key for hand touch whiteboard found”. (1) First check if the connection of USB cable is correct.(2) Please confirm if the USB cable has not been cut or spliced. (3) Please confirm if the system is equipped with a recovery ...

29 Important information Note: If you are a user of the product, please read the related warning information and product maintenance methods as below carefully. Before you install the product, please fully understand safetyinformation in the guide. It could prevent you from making mistakes, leading ...