Page 2 - Contents; Safety Notice
Contents Table of Contents Important Safety Notice .............................................................................................................................. 1 1. Product Specification ...............................................................................................
Page 3 - Important Safety Notice
1 Important Safety Notice Product Announcement: This product is certificated to meet RoHS Directive and Lead-Free produced definition. Using approved critical components only is recommended when the situation to replace defective parts. Vender assumes no liability express or implied, arising out...
Page 4 - Product Specification; General display parameters:
2 1. Product Specification 1.1 Scope: LCD BM190WX2-TJA1 LM190WX2-TJA1 is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in t...
Page 5 - Optical Characteristics:
Page 8 - regions.The adapter output cable length of 1500
6 1.3.1 Interface Connectors: 1.3.1.1 Power Adaptor and Connector: The AC inlet connector shall be an IEC 320-C13 male power receptacle for connection to mains power. The power cord shall be gray or black with length of 1.8m + 10cm/-0cm. The power cord type is different from regions.The adapter ...
Page 13 - The panel shall be a FULL HD resolution 19” diagonal TFT-LCD.
11 1.3.4.2 Factory Assigned Display Modes: 1.4 Flat Panel: 1.4.1 General Requirements: The panel shall be a FULL HD resolution 19” diagonal TFT-LCD. 1.4.2 Polarizer Hardness: The front polarizer should have hard coating (3H) and anti-glare treatment. 1.4.3 Backlight Requirements:
Page 15 - is defined as; For more information see Figure 8.
13 Surface luminance is the luminance value at center 1 point(1) across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 8. The variation in surface luminance , WHITE is defined as Minimum (P1,P2 …..P9) WHITE = -----------------------------...
Page 19 - Display type
17 Picture OSD Setting Information d. Item page status Status Display type Non-Focus Item focused Item selected
Page 24 - ITEM DESCRIPTION QT'S; PE BAG FOR STAND; STAND; ENERGY STAR CARD; CD MENUAL
22 3.2 Packing Exploded Diagram: ITEM DESCRIPTION QT'S 1 23456789 101112131415 CARTONEPS-1EPS-2 EPE BAG FOR MONITROT HEAR OF MONITORPE BAG FOR BASEBASE PE BAG FOR STAND STAND POWER CABLE SIGNAL CABLEQSG WARRANTY CARD ENERGY STAR CARD CD MENUAL 1111111111111111 ADAPTER 16
Page 25 - Assembly and Disassembly Procedures
23 4. Assembly and Disassembly Procedures 4.1 Assembly Procedures: Prepare a main board, an I/O Bracket and a Mylar. Assemble every part as the below picture. ① Turn over the main board and Lock screw. ② Turn over the main board and lock the four screws. ③ Paste the AL tape ④ Assemble the mylar ...
Page 26 - Mark
24 Connect FFC cable and fix Mainboard: ① Connect panel pcb and main board with FFC cable ② Paste the tape. ③ Follow the two marks to fix the main board on the back cover and then paste the AL tape. Connect the all cable and the paste all tapes as the below picture: S3 2 S4 S3 1 Mark 2 3 Mark Ma...
Page 30 - Separate the key board and the bezel.
28 Remove the panel. Separate the key board and the bezel. S7 S8
Page 36 - S1. These three files must be put in one folder as the below picture.
34 New F/W 6.2 Connection: 6.3 ISP Programming Procedures: S1. These three files must be put in one folder as the below picture.
Page 41 - Writing EDID Process; Hardware and Software Required:
39 7. Writing EDID Process 7.1 Test Environment Preparation: Hardware and Software Required: - LPT cable(male to male) - VGA cable -12V DC adapter - ISP Board: 715GT034-B - PC - Monitor - LPT port driver - ISP tool: TPVDDC20100901.exe - EDID LPT cable(male to male) VGA cable 12V DC adapter ISP...
Page 47 - HINGE ASSY
45 8. FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Acer V183HV-V193HQV. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING F...
Page 50 - Schematics and Layouts; Main Board
48 9. Schematics and Layouts 9.1 Schematics Main Board 715G4734M01000004I (DVI only for s190wl BD) BI N0- BIN0 GI N0 U101 FM24C02A A0 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 WP 7 VCC 8 HSIN0 VSI N0 DDCSCL_A DDCSDA_A C113 NC/ 22pF 50V C112 NC/ 22pF 50V BIN0 DET_VGA EDI D_WP GI N0 R I N0- GI N0- BIN0- RIN0 ...
Page 54 - Key Board
52 Key Board 715G4982K0D000003S R003 1K 1/10W 5% ZD001 MLVS0603M04 1 2 LBADC2 POWER_Key ZD004 NC 1 2 ZD003 NC 1 2 VOL- AU T O Z D005 NC 1 2 VOL + ZD006 NC 1 2 ZD007 NC 1 2 ZD008 NC 1 2 ME NU SW 001 SW CN001 Wire Harnes s 1 2 3 4 5 6 LED_BLUE# SW002 SW SW 003 SW SW004 SW SW005 SW SW006 SW POW E...