Page 3 - English; Special notes on LCD monitors; Safety instructions; Cleaning your monitor; Connecting/disconnecting the device
iii PB English Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. ...
Page 4 - Accessibility; Warnings; Using electrical power
v iv English Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To ...
Page 5 - Product servicing
v iv English extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the bra...
Page 6 - Potentially explosive environments; Additional safety information
vii vi English Potentially explosive environments Switch off your device in any area with a potentially explosive atmosphere and obey all signs and instructions. Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas ...
Page 7 - Disposal instructions; Tips and information for comfortable use
vii vi English Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics Equipment (WEEE) regulations, visit...
Page 8 - Finding your comfort zone
ix viii English • numbness, or a burning or tingling sensation • aching, soreness or tenderness • pain, swelling or throbbing • stiffness or tightness • coldness or weakness If you have these symptoms, or any other recurring or persistent discomfort and/or pain related to computer use, consult a phy...
Page 9 - Developing good work habits
ix viii English Display • Keep your display clean. • Keep your head at a higher level than the top edge of the display so your eyes point downward when looking at the middle of the display. • Adjust the display brightness and/or contrast to a comfortable level for enhanced text readability and graph...
Page 10 - Declaration of Conformity
Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail:[email protected] And, Acer Italy s.r.l Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it Declare under o...
Page 11 - Federal Communications Commission
Acer America Corporation 333 West San Carlos St., San Jose Suite 1500 CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.acer.com Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condit...
Page 13 - Unpacking
English 1 PB Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor Quick start guide HDMI cable (Option) D-sub cable DVI cable (Optional) AC Power cord Audio cab...
Page 14 - ATTACHING THE BASE; SCREEN POSITION ADJUSTMENT
English 3 2 ATTACHING THE BASE Remove: Reve rse the steps to remove the base. SCREEN POSITION ADJUSTMENT To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold the edges of the monitor as shown below. The monitor can be adjusted to 25 degrees up or 5 de...
Page 15 - Connecting the Power cord
English 3 2 Connecting the Power cord • Check first to make sure that the power cord you use is the correct type required for your area. • The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one en...
Page 16 - Connector pin assignment
English 5 4 Connector pin assignment 1 5 6 10 11 15 15-pin color display signal cable PIN No. Description PIN No. Description 1 Red 9 +5 V 2 Green 10 Logic ground 3 Blue 11 Monitor ground 4 Monitor ground 12 DDC-serial data 5 DDC-return 13 H-sync 6 R-ground 14 V-sync 7 G-ground 15 DDC-serial clock 8...
Page 18 - Standard timing table
English PB 6 Standard timing table Mode Resolution 1 VGA 640x480 60 Hz 2 MAC 640x480 66.66 Hz 3 VESA 720x400 70 Hz 4 SVGA 800x600 56 Hz 5 SVGA 800x600 60 Hz 6 XGA 1024x768 60 Hz 7 XGA 1024x768 70 Hz 8 VESA 1152x864 75 Hz 9 SXGA 1280x1024 60 Hz 10 VESA 1280x720 60 Hz 11 WXGA 1280x800 60 Hz 12 WXGA+ 1...
Page 19 - Installation; Steps
English 7 PB Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cable a Make sure both the monitor and computer are switched off. b Connect the VGA video cable to the computer. c Connect the digital cable (only for dual-input models).(1)...
Page 20 - Users controls; empowering Technology; MENU OSD functions; Volume adjust; INPUT Input Key
9 8 English Users controls Power Switch / Power LED: To turn the monitor ON or OFF.Lights up to indicate the power is turned ON. Using the Shortcut Menu AUTO Input Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly accessed settings. empo...
Page 21 - Acer eColor Management; mpowering Technology; Operation instructions
9 8 English Acer eColor Management mpowering Technology Movie Graphics Standard ECO User Adjust/Exit Operation instructions Step 1: Press “ “ Key to open the Acer eColor Management OSD and access the scenario modes Step 2: Press “ / “ or “ / ” to select the mode Features and Benefits Step 3: Press “...
Page 22 - Adjusting the OSD settings; OFF
11 10 English Adjusting the OSD settings Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor.Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD po...
Page 23 - Adjusting the OSD position
11 10 English Adjusting the OSD position Exit Enter OSDOSD Timeout 10 1. Press the MENU key to bring up the OSD.2. Using the directional keys, select OSD from the on screen display. Then navigate to the feature you wish to adjust.
Page 24 - Adjusting the setting
13 12 English Adjusting the setting Exit Enter SettingWide ModeDDC/CI ACMInputLanguageReset Full ON OD Normal OFF VGA English 1. Press the MENU key to bring up the OSD.2. Using the / / / keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3. The Setting menu can be us...
Page 25 - Product information; Information
13 12 English Product information Exit Information S/N: ETRLA00803104000502400 1920x1080 H:68KHz V:60Hz VGA Input 1. Press the MENU key to bring up the OSD.2. Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input.
Page 26 - Troubleshooting; VGA Mode
English 15 14 Troubleshooting Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. VGA Mode Problem LED status Remedy No picture visible Blue Using the OSD menu, adjust brightness and contrast to maximum or reset to t...
Page 27 - DVI mode
English 15 14 DVI mode Problem LED status Remedy No picture visible Blue Using the OSD menu, adjust brightness and contrast to maximum or reset to their default settings. Off Check the power switch. Check if the AC power cord is properly connected to the monitor. Amber Check if the video signal cabl...
