Page 3 - Special notes on LCD monitors; Safety
iii PB Special notes on LCD monitors The following are normal with the LCD monitor and do not indicate a problem. • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the power switch and then turn it on again to make sure the flicker disappears. • You ma...
Page 4 - iv
v iv Accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power from the equipment, be sure to unplug the power cord from the electrical outlet. Safe listening To protect ...
Page 5 - Product
v iv power company. • Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord. • If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extensio...
Page 6 - vii; Potentially
vii vi personnel when: • the power cord or plug is damaged, cut or frayed • liquid was spilled into the product • the product was exposed to rain or water • the product has been dropped or the case has been damaged • the product exhibits a distinct change in performance, indicating a need for servic...
Page 9 - Developing
ix viii • minimizing room light by using drapes, shades or blinds • using a task light • changing the display’s viewing angle • using a glare-reduction filter • using a display visor, such as a piece of cardboard extended from the display’s top front edge • Avoid adjusting your display to an awkward...
Page 10 - Declaration of Conformity; May; Date; Year to begin affixing CE marking 201 .
Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan And, Acer Italy s.r.l. Via Lepetit, 40, 20020 Lainate (MI) Italy Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it We, Acer Incorporated, hereby declare under our sole responsibili...
Page 11 - LCD Monitor
Federal Communications Commission Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference ...
Page 12 - The Function page; Trouble shooting
Special notes on LCD monitors iii Information for your safety and comfort iii Safety instructions iii Cleaning your monitor iii Connecting/disconnecting the device iii Accessibility iv Safe listening iv Warnings iv Using electrical power iv Product servicing v Potentially explosive environments vi A...
Page 13 - English; Unpacking
English 1 Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future. LCD monitor Quick start guide DVI-DL cable DP cable (Optional) HDMI cable (Optional) AC Power cord
Page 14 - ttaching
English 2 A ttaching / R emoving the base 1. Remove the monitor from the packaging. 2. Attach the footstand to the monitor, attach the base to the footstand. 3. Secure the base to the stand by turn the screw clockwise using a screwdriver or a suitable coin.
Page 15 - Screen position adjustment
English 3 Screen position adjustment To optimize the viewving position, you can adjust the monitor tilt by using both of your hands to hold the edges of the monitor as shown below. The monitor can be adjusted to 1 5 degrees up or 5 degrees down.
Page 16 - Connecting the Power cord
English 5 4 Connecting the Power cord • Check first to make sure that the power cord you use is the correct type requiredfor your area. • The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one end...
Page 17 - Connector pin assignment
5 4 Connector pin assignment 19-Pin Color Display Signal Cable* * only for certain models 20-Pin Color Display Signal Cable* * only for certain models PIN Meaning PIN Meaning 1. TMDS Data2+ 10. TMDS Clock+ 2. TMDS Data2 Shield 11. TMDS Clock Shield 3. TMDS Data2- 12. TMDS Clock- 4. TMDS Data1+ 13. C...
Page 19 - PB; Standard timing table
English 7 PB Standard timing table No. Mode Resolution Refr esh Rate 1 VGA 640x480 60 Hz 2 640x480 72 Hz 3 MAC 640x480 66.7 Hz 4 VESA 720x400 70 Hz 5 SVGA 800x600 56 Hz 6 800x600 60 Hz 7 800x600 72 Hz 8 XGA 1024x768 60 Hz 9 1024x768 70 Hz 10 VESA 1152x864 75 Hz 11 1280x960 60 Hz 12 SXGA 1280x1024 60...
Page 20 - Installation; Steps
English 8 Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect cable s 2 Connect the power cord Connect the power cord to the monitor, then to a properly grounded AC outlet. 3 Turn on the monitor and computer Turn on the monitor first, then the comp...
Page 21 - Users controls
9 Users controls Function key a. Monitor power off status Press to switch power on. In the normal display, anytime to Press more than 5 seconds switch to turn off the power. b. Blue indicates power on. Amber flicker indicates standby/power saving mode. No light display indicates Power off. c. Press ...
Page 22 - Adjusting the OSD settings; Main Page
10 Adjusting the OSD settings The OSD (on-screen display) can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings, please refer to following page: Main ...
Page 23 - Brightness; control and select the; brightness; setting using the arrows.; press the joystick to exit current page and store
11 Selecting the Input The input control and select DVI-D, DP ,HDMI or Auto Source. When you are done,press the joystick to exit current page and store. Adjusting the Brightness settingOpen the Brightness control and select the brightness setting using the arrows. When you are done, press the joysti...
Page 24 - back one level
12 The Function page Open the Function page to adjust the functions, settings which you want using the arrows. When you are done, toggle the joystick to the left or right to go back one level Adjusting the Picture 1. Press the MENU key to bring up the OSD. 2. Toggle the joystick to the up or down to...
Page 26 - Toggle the joystick to the up or down to select Audio from the; Adjusting
14 Adjusting the aduio 1. Press the MENU key to open the OSD. 2. Toggle the joystick to the up or down to select Audio from the OSD.Then toggle to the right to navigate to the element you wish to adjust and press the joystick to enter it. 3. Toggle to the left or right to adjust the sliding scales. ...
Page 29 - TROUBLESHOOTING; shooting list below to see if you can self-diagnose the problem.; Flicker
17 TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the trouble- shooting list below to see if you can self-diagnose the problem. ( DVI/ HDMI/ DP Mode) Problems Current Status Remedy No Picture LED ON Using OSD, adjust brightness and contrast to maximum or reset to their...
