Acer B233HL - Manuals - manualsarea.com

Page 2 - Downloaded from ManualMonitor.com Manuals

EN-1 SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate aproblem. N O T E S • Due to the nature of the fluorescent light, the screen may flicker duringinitial use. Turn off the Power Switch and then turn it on again to makesure the flicker disappears...

Page 3 - S af e t y i ns t r uc t i on s

EN-2 Information for your safety and comfort S af e t y i ns t r uc t i on s Read these instructions carefully. Keep this document for future reference. Follow allwarnings and instructions marked on the product. CA UT IO N fo r a cc es si bi li ty Be sure that the power outlet you plug the power cor...

Page 7 - AT T AC HING/ R E MO VI NG THE B ASE; Remove: Reverse the steps to remove the base.

EN-6 AT T AC HING/ R E MO VI NG THE B ASE Install: Align the base with the stand and push the base towards the top ofthe monitor, and then rotate the base clockwise until it stops. Tighten thescrew clockwise. Remove: Reverse the steps to remove the base. Downloaded from ManualMonitor.com Manuals

Page 8 - SCR E EN P O SI T IO N ADJUST MENT; T i l t; Please see the illustration below for an example of the tilt range.; He igh t Adj ust me nt

EN-7 SCR E EN P O SI T IO N ADJUST MENT In oder to optimize the best viewing position, you can adjust the height/tilt/swivel of the monitor. • T i l t Please see the illustration below for an example of the tilt range. • He igh t Adj ust me nt After pressing the top of the monitor, push the lock but...

Page 9 - S w i v e l

EN-8 • S w i v e l With the built-in pedestal, you can swivel the monitor for the mostcomfortable viewing angle. Downloaded from ManualMonitor.com Manuals

Page 10 - Do not expose the monitor to rain, excessive moisture, or dust.; CLEANI NG YOUR MO NI TO R; Always unplug the monitor before cleaning.

EN-9 CO NNEC TING THE P OWE R CO RD • Check first to make sure that the power cord you use is the correct typerequired for your area. • This monitor has a universal power supply that allows operation in either100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one end of...

Page 11 - S t a t e; ON

EN-10 Po wer savi ng The monitor will be driven into Power Saving” mode by the control signalfrom the display controller, as indicated by the amber-color power LED. The power saving states will be kept until a control signal has been detectedor the keyboard or mouse is activated. The recovery time f...

Page 12 - C ONNEC T O R P IN ASSI GNMENT

EN-11 P IN N O. D E S C RIP T ION P IN N O. D E SC R IP T ION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. DDC-return 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground C ONNEC T O R P IN ASSI GNMENT 15-Pin Co...

Page 14 - Sta ndard Timi ng Ta ble; Mo d e

EN-13 Sta ndard Timi ng Ta ble Mo d e R e so lu tio n 1 VGA 640x480 60 Hz 2 MAC 640x480 60.66 Hz 3 VESA 720x400 70 Hz 4 SVGA 800x600 56 Hz 5 SVGA 800x600 60 Hz 6 XGA 1024x768 60 Hz 7 XGA 1024x768 70 Hz 8 VESA 1152x864 75 Hz 9 SXGA 1280x1024 60 Hz 10 WXGA 1280x800 60 Hz 11 WXGA+ 1400x900 60 Hz 12 UXG...

Page 16 - USE R CO NTR OLS; Fro nt Pa nel Contr ols

EN-15 USE R CO NTR OLS Fro nt Pa nel Contr ols 1.Power Switch:To turn ON or OFF the power. 2.Power LED:Lights up to indicate the power is turned ON. 3.Empowering / Exit:1) When OSD menu is in active status, this button will act as EXIT-KEY(EXITOSD menu).2) When OSD menu is in off status, press this ...

Page 17 - HOW TO ADJUST A SETTING; Op er at io n in st ru ct io ns

EN-16 II. Only Dual Input Model I. Only Analog Input Model B . U SE R If selected to “USER” item, will appear the Standard OSD A . Acer eColor Management If selected to “Acer eColor Management “ item, will appear the Acer eColor” OSD HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the O...

Page 18 - ADJUSTING THE PICTURE; The descriptions for function control LEDS

EN-17 • ADJUSTING THE PICTURE The descriptions for function control LEDS A. Acer eColor Management B. USER Ma in Me n u ico n S u b Me n u ic o n S u b Me n u ite m D e s cr ip tio n N/A User mode User defined. Settings can be fine-tuned to suit any situation N/A ECO mode A d j u s t s t h e s e t t...

Page 21 - T R O UB LE S HO O T I NG; Problems

EN-20 (VGA Mode) T R O UB LE S HO O T I NG Before sending your LCD monitor for servicing, please check the trouble-shooting list below to see if you can self-diagnose the problem. Problems Current Status Remedy No Picture LED ON · Using OSD, adjust brightness and contrast to maximum or reset to thei...

Page 23 - Declaration of Conformity; A cer Incorporat ed; LCD Monitor

Declaration of Conformity We , A cer Incorporat ed 8F, 88, Sec. 1, Hsin Tai Wu Rd ., H sich ih, Taipei Hsien 221, Taiwan Contact Person: Mr. Easy Lai, E-mail: ea sy_lai@ace r. com. tw And , Acer E ur ope SA Via Canton ale, Centro Galleria 2 6928 Ma nno Switzerla nd H ereby dec lare that: Product: LC...